Broadcom BCM1125 User Manual Download Page 158 | Manualshive

Page: 158 / 516

background image

BCM1250/BCM1125/BCM1125H

User Manual

10/21/02

B r o a d c o m C o r p o r a t i o n

Page

130

Section 6: DRAM

Document

1250_1125-UM100CB-R

The drive position of the data relative to clock (t4 and t5) is controlled by the addr_skew parameter in the same
way as the address, except the data changes on both edges of the clock. The data transition point is thus offset
from both edges of the Mn_CLK by about 16% to 34% of the memory clock cycle time.

The third use of a DLL is to position the DQS strobe relative to the data during a write to the memory. The DQS
transition needs to be shifted to the center of the data valid window. This is done by shifting the DQS transition
from the data transition using a DLL controlled by the dqo_skew. The minimum delay between the data and
DQS (t6 in

) is about 16% of the cycle time when dqo_skew is 4'b0000, the maximum (shown as t7)

is about 34% of the cycle time with dqo_skew set to 4'b1111.

The second and third uses of the DLL interact to set the position of the DQS output relative to the clock. The
difference between the addr_skew and dqo_skew controls this delay (if they are set to the same value the
strobe will line up with the clock). The early DQS shown by t2 results from the addr_skew being set to

M

=4'b1111 and dqo_skew to

M

=4'b0000, the difference in the delays will make the DQS precede the clock by

(35 - (-35)) = 70% of a quarter cycle or 17.5% of the cycle time. The late DQS shown by t3 is the reverse
situation and will have the DQS 17.5% of the cycle time after the clock.

Figure 21: Timing Relationships Set by DLLs

Mn_CLK

ADRCTLearly

ADRCTLlate

DATAearly

DATAlate

DQSOUTearly

DQSOUTlate

t0

t1

t2

t3

t4

t5

t6

t7

Address delay from clock is 16%-34% of cycle set by addr_skew

DQS out delay from clock is -17.5% to +17.5% of cycle, set by difference between addr_skew and dqo_skew

Data delay from clock is 16%-34% of cycle set by addr_skew

DQS delay from data is 16%-34% of cycle set by dqo_skew

«
...
156
157
158
159
160
...
»

Summary of Contents for BCM1125





































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for BCM1125

Brand: Aastra Pages: 2

Brand: Patton electronics Pages: 51

Brand: TC Electronic Pages: 55

Brand: Yamaha Pages: 24

Brand: Yamaha Pages: 5

Brand: Vonets Pages: 8

USB-BRIDGEV2-EVAL

Brand: IDT Pages: 11

Brand: Nvidia Pages: 115

Brand: UNA AUTOMATION Pages: 20

Brand: FONESTAR Pages: 8

Brand: Z3 Technology Pages: 67

Brand: Idis Pages: 16

Brand: ZIMO Pages: 13

EK-FC750 GTX Series

Brand: ekwb Pages: 2

ipRocketLink IAD 3086

Brand: Patton electronics Pages: 12

Brand: Alesis Pages: 11

Brand: NXP Semiconductors Pages: 1202

Brand: Dave Embedded Systems Pages: 79

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands