Broadcom BCM1125 User Manual Download Page 105 | Manualshive

Page: 105 / 516

background image

User Manual

BCM1250/BCM1125/BCM1125H

10/21/02

B r o a d c o m C o r p o r a t i o n

Document

1250_1125-UM100CB-R

Section 4: System Control and Debug Unit

Page

77

All entries in the trace buffer contain an address/control bundle. The bundle includes the response phase
signals that match with the address phase signals that are captured. The data phase signals are captured at
the same time as the A phase signals, and have no relationship with the transaction that the A-phase and R-
phase are part of. The address/control bundle is 128 bits organized as shown in

.

17:10

trcAddr

8‘b0

Current trace buffer address. If the trcFull bit is not set this number plus 1 entries can be
read from the buffer.

63:18

notimp

46‘bx

Not Implemented.

Table 48: Trace Control Register

(Cont.)

trace_cfg -

00_1002_0A00

Bits

Field

Default

Description

Table 49: Trace Buffer Address/Control Bundle

Bits

Field

Description

2:0

D_CODE

Data code (this has no relationship to the A and R phase signals).
000: NOP, data invalid (gets counted as arbitrated but not used).
001: Data valid.
010: Data valid, tag ECC corrected (L2).
011: Data valid, data ECC corrected (Mem, L2).
100: Bus error (IO bridge).
101: Fatal bus error (cache block ownership unclear).
110: Uncorrectable tag ECC error (L2).
111: Uncorrectable data ECC error (CPU, L2, Mem).

3

D_MOD

D-phase indication that the data is dirty (this has no relationship to the A and R phase signals).

7:4

D_RSP[3:0]

Data phase responder ID (this has no relationship to the A and R phase signals).

17:8

D_ID[9:0]

Data phase transfer ID (this has no relationship to the A and R phase signals).
[9:6] requester ID.
[5:0] unique number within requester.

18

R_L2HIT

The L2 hit during the response phase of the A-phase transaction.

24:19

R_EXC[5:0]

Response phase exclusive bits that match the A-phase transaction.

30:25

R_SHD[5:0]

Response phase shared bits that match the A-phase transaction.

31

A_L2CA

L2 cacheablility bit.
0: Do not allocate on miss.
1: Allocate on miss.

36:32

reserved

Always reads zeros.

37

int_trace_1

Records the int_trace_trigger_1 output from the CPU 1 interrupt mapper (see Figure 8)

38

int_trace_0

Records the int_trace_trigger_0 output from the CPU 0 interrupt mapper (see Figure 8)

39

Dvalid

Set if the data bus had a valid cycle when the sample was captured (indicates the D_
signals are valid)

40

Avalid

Set if the address bus had a valid cycle when the sample was captured (indicates the A_
and R_ signals are valid).

51:41

BLOCK[10:0]

ZBbus blocker signals.

59:52

A_BYT

Encoded byte enables. Indicates valid bytes within doublewords.

BYT[n=7:0] =A_BE[n] | A_BE[n+8] | A_BE[n+16] | A_BE[n+24]

«
...
103
104
105
106
107
...
»

Summary of Contents for BCM1125





































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for BCM1125

AllShare Cast Dongle

Brand: Samsung Pages: 2

Brand: D-Link Pages: 14

Brand: Magma Pages: 2

Brand: Edge-Core Pages: 7

Brand: Industrex Pages: 51

Brocade X6-8 Director

Brand: Broadcom Pages: 207

Brand: Phytec Pages: 53

Brand: ZyXEL Communications Pages: 2

Brand: Dahua Pages: 24

Brand: SIIG Pages: 20

Brand: Dantel Pages: 62

Brand: AXIOMTEK Pages: 58

Brand: Microchip Technology Pages: 9

Brand: XtendLan Pages: 21

Brand: Ariesys Pages: 10

EK-FC750 GTX Series

Brand: ekwb Pages: 2

Brand: Aaeon Pages: 119

TeleMyo 2400T V2

Brand: Noraxon Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands