Broadcast Tools SS 16.1 Installation And Operation Manual Download Page 3

e-mail: 

[email protected]   

voice: 

360.854.9559   

fax: 

866.783.1742 

3

SS 16.1 Installation and Operation Manual

INTRODUCTION

INTRODUCTION

Thank you for your purchase of a Broadcast Tools

®

16 x 1 Sixteen Input, Single

Output Stereo Switcher/Router

, (referred to as the 16 x 1 throughout this manual).

We’re confident that this product will give you many years of dependable service.
This manual is intended to give you all the information needed to install and oper-
ate the Broadcast Tools

®

16 x 1 Sixteen Input, Single Output Stereo Switcher/Router.

SAFETY INFORMATION

Only qualified personnel should install Broadcast Tools

®

products.  Incorrect or

inappropriate use and/or installation could result in a hazardous condition.

WHO TO CONTACT FOR HELP

If you have any questions regarding your product or you need assistance, please con-
tact your distributor from whom you purchased this equipment.

If you would like more information about Broadcast Tools® products, you may
reach us at:

Broadcast Tools,  Inc.

131 State Street
Sedro-Woolley, WA 98284  USA
Voice:

360 . 854 . 9559

Fax:

866 . 783 . 1742

Internet Home Page:www.broadcasttools.com
E-mail:

[email protected]

THANK YOU FOR CHOOSING 

BROADCAST TOOLS

®

BRAND PRODUCTS!

CAUTION!

Broadcast Tools®

Products, as with any
electronic device, can
fail without warning.
Do not use this product
in applications where a
life threatening condition
could result due to failure.

NOTE:

This manual should be
read thoroughly before
installation and operation.

Broadcast Tools is a Veteran Owned Business

Designed, Assembled and Supported in WA State, USA

Summary of Contents for SS 16.1













Reviews: