Broadcast Tools Silence Sentinel Basic Installation And Operation Manual Download Page 3

e-mail: 

[email protected]   

voice: 

360.854.9559   

fax: 

866.783.1742

3

Silence Sentinel

®

Basic Installation and Operation Manual

INTRODUCTION

INTRODUCTION

Thank you for your purchase of a Broadcast Tools® “Silence Sentinel®

Basic” (referred to as the Silence Sentinel® Basic throughout this manual). We’re
confident that this product will give you many years of dependable service. This
manual is intended to give you all the information needed to install and operate the
Broadcast Tools® “Silence Sentinel® Basic”.

SAFETY INFORMATION

Only qualified technical personnel should install Broadcast Tools products.

Any attempt to install this device by a person who is not technically qualified could
result in a hazardous condition to the installer or other personnel or damage
Broadcast Tools product or other equipment.  Please ensure that proper safety pre-
cautions have been taken before installing this device.  If you are unfamiliar with
this type of equipment, please contact a properly qualified engineer to handle the
installation and setup of the Broadcast Tools product.

Broadcast Tools, Inc., is unable to support NON-Broadcast Tools software, hard-

ware or NON-Broadcast Tools computer/hardware/software problems.  If you experience
these problems, please research your hardware/software instruction manuals or contact the
manufacturers technical support department.

WHO TO CONTACT FOR HELP

If you have any questions regarding your product or you need assistance,

please contact your distributor from whom you purchased this equipment.

If you would like more information about Broadcast Tools® products, you

may reach us at:

Broadcast Tools,  Inc.

131 State Street
Sedro-Woolley, WA 98284-1540 USA
Voice: 360.854.9559
Fax:

866.783.1742

Internet Home Page: www.broadcasttools.com
E-mail:

[email protected]

THANK YOU FOR CHOOSING 

BROADCAST TOOLS® BRAND PRODUCTS!

CAUTION!

Broadcast Tools®

Products, as with any
electronic device, can
fail without warning.
Do not use this product
in applications where a
life threatening condition
could result due to failure.

NOTE:

This manual should be
read thoroughly before
installation and operation.

WEBSITE:

Visit our web site for
product updates and
additional information.

Broadcast Tools is a Veteran Owned Business

Designed, Assembled and Supported in WA State, USA

Summary of Contents for Silence Sentinel Basic















Reviews: