Broadcast Tools ACS 8.2 Plus Installation And Operation Manual Download Page 3

e-mail: 

[email protected]   

voice: 

360.854.9559   

fax: 

866.783.1742 

3

Broadcast Tools

®

ACS 8.2 Plus Eight Input, Dual Output StereoMatrix Audio Control Switcher

INTRODUCTION

INTRODUCTION

Thank you for your purchase of a 

Broadcast Tools® ACS 8.2 PLUS EIGHT

INPUT, DUAL OUTPUT STEREO MATRIX AUDIO CONTROL SWITCHER

(referred to as the ACS 8.2 Plus throughout this manual).  We’re confident that this
product will give you many years of dependable service. This manual is intended to
give you all the information needed to install and operate the Broadcast Tools

®

ACS 8.2 Plus.

Broadcast Tools, Inc., is unable to support NON-Broadcast Tools hardware/software
or NON-Broadcast Tools computer hardware/software problems.  If you experience
these problems, please research your hardware/software instruction manuals or
contact the manufacturer’s technical support department.

SAFETY INFORMATION

Only qualified personnel should install Broadcast Tools

®

products.  Incorrect or

inappropriate use and/or installation could result in a hazardous condition.

WHO TO CONTACT FOR HELP

If you have any questions regarding your product or you need assistance, please con-
tact your distributor from whom you purchased this equipment.

If you would like more information about Broadcast Tools

®

products, you may reach

us at:

Broadcast Tools,  Inc.

131 State Street
Sedro-Woolley, WA 98284 USA
Voice: 360 . 854 . 9559
Fax:

866 . 783 . 1742

Internet Home Page: www.broadcasttools.com
E-mail:

[email protected]

THANK YOU FOR CHOOSING 

BROADCAST TOOLS

® 

BRAND PRODUCTS!

CAUTION!

Broadcast Tools

®

Products, as with any
electronic device, can
fail without warning.
Do not use this product
in applications where a
life threatening condi-
tion could result due to
failure.

NOTE:

This manual should be
read thoroughly before
installation and opera-
tion.

WEBSITE:

Visit our web site for
product updates and
additional information.

Summary of Contents for ACS 8.2 Plus
























Reviews: