Briteq BTX-HAWK, Operation Manual

Page: 8 / 24

ENGLISH OPERATION MANUAL
BRITEQ
®
6/19 BTX-HAWK
General instructions for setup.
The SETUP-menu has three logically structured levels, see the menu structure on the previous page.

Press the [MENU] button to enter the SETUP-menu. (Press about 3s while Menu [LOCK] function is
active)

Press the
▲/▼/◄/► buttons to browse the different functions of the setup menu until the required function
is shown on the display.

Press the [ENTER] button to access the function and change its parameters.

Use
▲/▼ buttons to change the value.

Press the [ENTER] button again confirm.

To jump to a higher menu level: press the [MENU] button.

To exit the SETUP-menu: press the [MENU] button several times until the standard display is shown.
Remark: to make things easier you will always enter the SETUP-menu at the last used location.
[SET CONFIG > ADDRESS Set]
–
All functions in this level are related to addressing of the unit.
[DMX-Address]
Used to set the desired DMX-address.

Press the
▲/▼/◄/► buttons until the desired function is showing on the display.

Press the [ENTER] button: the values can be changed

Use
▲/▼ buttons to select the desired DMX512 address. The last occupied DMX-address is also shown:
makes it easier to set the address of the next unit in the chain.

Once the correct address shows on the display, press the [ENTER] button to confirm.
[SET CONFIG > CHAN. Mode]
Used to set the desired channel mode.

Press the ▲/▼/◄/► buttons until the desired function is showing on the display.

Press the [ENTER] button: the values can be changed

Use ▲/▼ buttons to select the desired mode:

5MSL mode: [PAN/TILT] are music controlled while the dimmer, strobe speed, gobos, colors &
[PAN/TILT]
–speed can be set using only 5 DMX channels.

13 CH mode: Full DMX-control for all functions.

15 CH mode: same as the 13CH mode but with 16bit [PAN/TILT] movements .

Once the correct option shows on the display, press the [ENTER] button to confirm.
[SET CONFIG > SHOW Config]
–
All functions in this level are related to the automatic shows.
[NO DMX Mode]
Used to set how the projector reacts when the DMX-signal disappears.

Press the ▲/▼/◄/► buttons until the desired function is showing on the display.

Press the [ENTER] button: the values can be changed

Use ▲/▼ buttons to select the desired mode:

BLACKOUT: output turns black while no DMX is detected.

FREEZE: output based on the last valid DMX-signal is kept on the projector.

AUDIO: the projector starts working in audio mode.

Once the correct option shows on the display, press the [ENTER] button to confirm.
Note: as soon as the input detects a DMX-signal, blackout, freeze or audio mode will be cancelled.
[ShowMode]
Used to select the installation position of the projector while used in standalone mode.

Press the ▲/▼/◄/► buttons until the desired function is showing on the display.

Press the [ENTER] button to start editing.

Use the ▼/▲ buttons to select one of the available installation positions:

[Floor 180°]: Fixture is placed on the floor . [PAN/TILT] movements are not limited.

[CeilingHung]: Fixture is fixed on the ceiling . [TILT] movements are limited to ±60°.

[Stage Floor]: Fixture is placed on a stage, in front of the audience. The spot is always projecting
towards
the audience’s direction; i.e. in front of the stage. [PAN] movement angle (left to right to left):
160°. [TILT] movement angle: 90° (60° above horizon; 30° below horizon.)