![Britax MAX-FIX User Instructions Download Page 2](http://html.mh-extra.com/html/britax/max-fix/max-fix_user-instructions_2814045002.webp)
1.
Pull the grey fabric loop 11 to pull
out both locking arms 12 .
2.
Place the child seat in the direc-
tion of travel rearward-facing on
the vehicle seat.
INSTALLATION
3.
Grasp the child seat with both
hands and slide the two locking
arms 12
firmly into the insert
guides 02 until the locking arms
engage with a clicking noise on
both sides. The green ISOFIX in-
dicators 14 must now be visible
on both sides.
CaUTION!
The locking arms
are only correctly engaged if both
of the ISOFIX indicators 14 are
completely green.
5.
Pull the support leg as far away
from the back of the child seat as
possible.
A
correctly adjusted headrest 04 ensures optimal protection for your child in
the safety seat:
The headrest 04 must be adjusted so that the shoulder straps 06 are at the
same level as your child’s shoulders or slightly above.
The shoulder straps 06 must run at shoulder height or a little above the height
of the child’s shoulders.
►
The shoulder straps 06 must not run behind the back of the child or at ear
height or above the ears.
9.
Open the storage compartment 15 at the rear of the seat shell.
10.
Pull up the belt height adjuster 20 and adjust the headrest by sliding the
back plate higher or lower.
11.
Move the headrest 04 to the correct shoulder strap height and check that it
is properly engaged by lightly sliding the head rest 04 downwards.
6.
Push both adjustment buttons 18
and pull out the support leg 17
until it rests firmly on the floor
of the vehicle. The support leg
indicator 19 must be completly
green
CaUTION!
The support leg 07
must never be suspended in mid-
air or supported by other objects.
Also ensure that the support leg
17
does not raise the MAX-
FIX base 16 from the car seat
surface.
For the safety of your child, before every journey in the car check that...
• the child seat is engaged on both sides with the ISOFIX locking arms 12 in the ISOFIX attachment points 01 and that both ISOFIX indicators 14 are comple-
tely green;
• the child seat is securely fastened;
• the support leg is firmly on the vehicle floor and the support leg indicator
19 is green;
• the straps of the child seat are close to the body without constricting the child;
• the shoulder straps 06 are correctly adjusted and the straps are not twisted;
• the shoulder pads 05 are in the right position on your child‘s body;
• the buckle latches 21 are engaged in the harness buckle 07.
CaUTION!
If your child attempts to open the ISOFIX release buttons 13 or the harness buckle 07 , make sure to stop at the earliest opportunity. Check
that the child safety seat is correctly attached and make sure that your child is properly secured. Teach your child about the dangers involved.
removing the child seat with ISOFIX
1.
P
ush both adjustment buttons 18 and slide the lower section of the support leg 17 into the upper section until it is fully stored. Release the adjustment buttons
18
to fix it in its storred position
2.
Push the green ISOFIX indicator 14 and the red release button 13 on the two locking arms 12 towards each other. The locking arms 12 release.
3.
Slide the ISOFIX locking arms 12 back into the seat shell 26
→
A rattling noise is produced when the locking arms are pushed back in.
TIP: The locking arms are protected against damage when they are pushed back into the seat base.
CaUTION!
Remove the child safety seat from the vehicle.The child safety seat must never be transported in the car if it is not properly secured.
Preparatory work
1. If your vehicle is not equipped with the ISOFIX insert guides as
standard, clip the two insert guides
02
which are included with the
seat* with the cut-out facing upwards onto the two ISOFIX attach-
ment points
01
of your vehicle.
TIP: The ISOFIX attachment points are located between the surface
and the backrest of the vehicle seat.
2. Move the head restraint on the vehicle seat to the upper position.
* The insert guides make it easier to install the child safety seat with the aid of the ISOFIX
attachment points and prevent damage to the seat covering. When not in use, they should
be removed and stored in a safe place. On vehicles with a folding backrest the insert
guides must be removed before the backrest is folded.
Any problems which occur are usually caused by dirt or foreign objects on the insert gui-
des and on the hooks. Clean off any dirt or foreign objects to remedy this type of problem.
For the protection of all vehicle occupants
In the case of an emergency stop or an accident, persons or objects which are not properly secured in the car can cause injury to other vehicle
occupants. For this reason, please always check that...
• the backrests of the vehicle seats are locked (e.g. that the latch on a folding rear seat bench is engaged).
• all heavy or sharp-edged objects in the vehicle (e.g. on the parcel shelf) are secured.
• all persons in the vehicle have their seatbelts fastened.
• the child safety seat is always secured in the car via the ISOFIX anchoring, even when there is no child in the seat.
For the protection of your child
• The more snugly the harness fits over your child‘s body, the safer your child will be.
• Please do not ever leave your child unattended in the child safety seat in the vehicle.
• Use on the rear seat:
Move the front seat forward far enough that you child‘s feet cannot hit the backrest of the front seat (to prevent risk of injury).
• The child safety seat can get hot in direct sunshine. Caution: Children‘s skin is delicate and could be injured as a result. Protect the child
seat against intensive direct sunlight when it is not currently in use.
• Only allow your child to enter and exit the vehicle on the pavement side.
• Make stops during longer journeys to give your child an opportunity to run about and play.
To protect your vehicle
Some vehicle seat coverings made of more delicate materials (e.g. velour, leather, etc.) may develop wear marks when child seats
are used. For optimum protection of your seat covers, we recommend using the BRITAX RÖMER Car Seat Protector, which is
available from our range of accessories.
Take the time to carefully read through these instructions, and always keep them ready to hand in the designated pocket on the child seat.
SECURING YOUR CHILD
RECLINE POSITIONS
The MAX-FIX can be put into multiple
different positions.You can change
the recline position while the child is
installed in the car seat.
The most recline position gives your
child the most comfort for sleeping.
For younger children from 0-6 months
use the seat in its most recline position
with the infant insert to ensure your
child spine is supported whilst sleeping.
To change the positions turn the recline
wheel 10
.
7.
Shake the child safety seat to
make sure it is safely attached
and re-check to the ISOFIX indi-
cators 14 to make sure that both
of them are completely green.
Your car seat is now fully installed
8.
Follow the steps in the section „
SECURING YOUR CHILD“.
12.
Open the harness buckle 07 (press red button)
13.
Press the adjusting button 08 and at the same time pull both shoulder
straps 06 forwards. Do not pull on the shoulder pads 05 .
14.
Have your child sit down in the child seat.
15.
Guide the two buckle latches
21 together and engage them before putting
them into the harness buckle 07 - this should make a clicking noise.
16. Pull on the adjustment strap 09
until the harness lies flat and is close
against your child‘s body.
CaUTION!
Pull out the adjusting strap to the front.
CaUTION!
The hip straps 22 must be positioned as low as possible over
your child‘s hips.
INFANT INSERT
The infant insert can be used for child-
ren between 0 - 6 months.
The infant insert ensures your baby´s
spine is supported during travel.
Installation of the infant insert:
1.
Open the two plastic fasteners on
the infant insert
2.
Place the infant insert into the child
seat and lay both shoulder straps
06
over the infant insert
3.
Close both plastic fasteners
4.
Slide the harness buckle 07 and
the crotch pad through the ope-
ning of the infant insert.
CaUTION!
Make sure that your
child is always securely fastened.
4.
Push the child seat with a sub-
stantial amount of force as far
back as it will go.
01
02
12
11
14
12
02
17
18
19
16
14
04
06
15
20
07
06 05
08
21
07
22
09
10
06
07
23