manualshive.com logo in svg

Britax MARATHON CS, User Manual, Page: 17 / 23

Share
Download
Britax MARATHON CS User Manual Download Page 17

30

31

C

Chest Clip

Fastening the Chest Clip

Fasten  the  chest  clip  by  pushing  the  two  halves 

together until a positive click is heard (Fig. A).
Releasing the Chest Clip 

Squeeze the middle tabs together (Fig. B).

1 

Pull the two pieces apart.

2 

Adjusting the Chest Clip

Slide the chest clip up or down (Fig. C) on   the 

1 

harness so it is positioned at the middle of the 

child’s chest, level with the child’s armpits.

Slide the HUGS

2 

™

 chest pads and comfort pads 

to a comfortable location for the child.

HUGS™ Chest Pads

Child Seat Functions

Child Seat Functions

WARNING!

 

HUGS

™

 chest pads must 

be installed for forward-facing use. Removal of 

HUGS is optional only for rear-facing use.

b

A

Harness Buckle

Fastening the Harness Buckle

Hold the harness buckle with one hand.

1 

Use your other hand to insert one buckle tongue 

2 

at a time into the harness buckle (Fig. D). 

A  proper  connection  is  confirmed  with  a  positive 

• 

click after inserting each buckle tongue.

Releasing the Harness Buckle

Brace  the  rear  of  the  harness  buckle  with  one 

1 

hand.

Use your thumb to press the release button and 

2 

slide  both  buckle  tongues  to  remove  from  the 

buckle (Fig. E).

IMPORTANT: 

Periodically  clean  the  harness  buckle  to 

ensure safe operation (page 37).

x 2

x 2

e

x 2

x 2

d

Adjusting Harness Slot Height

IMPORTANT:

  See  Important  Harness  Adjustments  on 

pages 6–7 for instructions on proper harness fit based 

on your child’s height and weight.

Loosen the harness by lifting the harness adjuster 

1 

lever while pulling the harness straps forward as 

far as possible (Fig. F).

From the rear of the child seat, unhook the shoulder 

2 

harness from the harness yoke (Fig. G).

Pull  the  harness  straps  through  the  shell,  foam, 

3 

and cover to the front of the child seat. 

Thread the harness straps through the appropriate 

4 

harness  slots  in  the  cover,  foam,  and  child  seat 

shell (Fig. H).

Reattach the harness straps to the harness yoke 

5 

(Fig. G).

Pull  the  harness-adjuster  strap  to  tighten  the 

6 

harness.

Verify  that  all  straps  are  threaded  at  the  same 

7 

height and are not twisted. 

F

G

h

Summary of Contents for MARATHON CS
























Reviews:

No comments