manualshive.com logo in svg

Britax FORWARD FACING CHILD RESTRAINT, Instruction Book, Page: 9 / 10

Share
Download
Britax FORWARD FACING CHILD RESTRAINT Instruction Book Download Page 9

9

SUITABLE  FOR  USE

To be used only in a forward facing
position for a chlid weighing from
8 kg to 18 kg.

8 kg min.

18 kg max.

TO BE USED WITH A LAP-SASH OR LAP ONLY 
SEAT BELT IN THE FRONT OR BACK OF MOST 
CARS WITH FORWARD-FACING SEATS.

WARNINGS

Do not use

 the restraint without the Upper Anchorage Strap correctly attached.

If your vehicle is not fitted with an anchor point, please contact a Safety Restraint Fitting Station 
authorised by the relevant State Government Body for correct fitment of the restraint. In New 
Zealand contact the agent for the vehicle. The upper anchorage strap must be attached to an 
anchorage point using an extension strap if necessary. 

When using the restraint in the front seat, 

do

 

not

 

use

 

the

 

rear

 

seat. 

The upper anchorage strap 

will need to pass the rear seating position to attach to an anchorage point.

Do not use

 on any vehicle seat which faces

 

sideways or rearwards.

DO NOT USE 

A CHILD RESTRAINT IN A SEATING POSITION WHERE AN AIRBAG IS

 

FITTED. 

FOLLOW CAR MANUFACTURER’S

 

RECOMMENDATIONS.

HOW  TO  USE

12

?

Lift & hold 
Harness Adjuster Lock up
(Under Flap)

Pull to
lengthen

Pull to
tighten

Front of vehicle

PLACING  CHILD  IN  THE  RESTRAINT

A.

Lengthen  harness  by  lifting  Harness 
Adjuster  Lock  up  (under  flap)  while 
pulling  on  either  shoulder  strap  until  the 
harness  will  accomodate  the  child.

B.

Place child in the restraint and feed
each arm through shoulder straps. Pull
harness buckle up between child’s legs.

D.

TO  REMOVE  CHILD

Ensure slack is removed from harness lap strap by pulling shoulder 
straps then pull harness adjustment strap to adjust harness to a 
comfortable but firm fit. Check that slack in straps is minimal. 
Shoulder Harness Straps must fit firmly to the child. A loose 
harness could result in serious injury in an accident.                  

Do not

 use restraint if straps do not tighten and contact your local 

authorised service agent for repair.

Press red button on harness buckle then both harness tongues will 
be released. Lift the shoulder straps from the child’s shoulders.

Harness
Lap Strap

Crotch Straps

Shoulder
Strap

Pull to remove slack

from Harness Lap Strap

C.

Fit either harness tongue into the harness buckle followed by the other tongue until a click is 
heard. Should the second tongue not insert - press the red button and reinsert the tongues. 
Ensure secure engagement by pulling harness straps.

Click

B.

Summary of Contents for FORWARD FACING CHILD RESTRAINT











Reviews:

No comments