background image

3

Need help? 

Give us a call on 

0330 026 6273 

and speak to one of our trained advisors.  

Important Safety Information

•  Please read these instructions 

thoroughly and retain for future use.

 

•  All products manufactured and 

supplied by Bristan are safe provided 
they are installed, used correctly 
and receive regular maintenance in 
accordance with these instructions.

• 

If you are in any doubt about your 

ability to install this product safely 
you must employ the services of 
an experienced qualified plumber/
electrically qualified person.

•  This Digital Electronic Mixer 

Shower needs to be installed in 
accordance with, and meet the 
requirements of the Water Supply 
(Water  Fittings)  Regulations  1999  and        
Scottish Byelaws 2004.

   

 Before starting any installation          

    please consider the following:

•  Before drilling into walls, check 

that there are no hidden electrical 
wires, cables or water supply pipes. 
This can be checked with the aid of an 
electronic detector.

•  Do not install this shower unit in a 

room/environment without adequate 
ventilation or an extractor fitted. This 
is required to prevent condensation 
forming within the unit.

•  Do not operate the shower unit if 

the shower head or spray hose has 
been damaged or is blocked.

•  Do not block the flow of water 

from the shower head, by placing it 
(smothering it) on your hand or any 
other part of your body or foreign 
object.     

       

• Do not operate the shower if 
the water stops flowing during 
use  or  if  the  water  is  leaking  from                  
the Mixing Valve itself. Turn off at 
the mains  electrical supply and refer 
to the  Troubleshooting section or     
contact Bristan Customer Services on 
0330 026 6273.

 
 Warning:

 Do not operate this  

 

product if you suspect it is 

 

frozen. Do not site the Mixing  

 

Valve where it might be 

 

subjected to freezing conditions.

Warning:

 Before installing the 

new Digital Electronic Mixer 
Shower it is essential that you 
thoroughly flush through the 
pipe work in order to remove any 
remaining swarf, solder, etc. 
Failure to carry out this 
procedure could cause problems 
or damage to the workings of 
the Mixing Valve.

Summary of Contents for Wave Single Outlet Touchpad

















Reviews: