Brinkmann 810-6550-S Owner'S Manual Download Page 18

17

Problem

Possible Cause

Prevention/Cure

Flame blows out

High or gusting winds

Do not use grill in high winds

Low on LP gas

Replace or refi ll LP gas tank

Burner holes may be obstructed

Refer to “Burner Assembly/Maintenance” instructions

Flow limiting device tripped

Refer to “Regulator Resetting Procedure”

Flare-up

Grease buildup

Clean all grill parts per “Proper Care and Maintenance” instructions

Excess fat in meat

Trim fat from meat before grilling

Excessive cooking temperature

Adjust (lower) cooking temperature

Grease fi re

Grease trapped by food buildup around burner 
system

1. Turn control knobs and LP gas tank valve to “OFF”
2. Leave lid in open or closed position and let fi re burn out. Use BC               

type fi re extinguisher or baking soda, sand or dirt to smother fi re, 
if necessary.

3. After grill cools, remove and clean all parts per “Proper Care and 

Maintenance” instructions 

Flashback (fi re in burner 
tubes) / knobs melting

Burner and/or burner tubes are blocked

Clean burners and/or burner assembly

Inside of lid is peeling 
(like paint peeling)

Baked on grease buildup has turned into carbon 
and is fl aking off

Clean thoroughly per “Proper Care and Maintenance” instructions

GRILL COOKING TIPS:

CLEANLINESS:

• 

Always wash hands thoroughly with soap and hot water prior to handling food and after handling raw 
meat, uncooked poultry or seafood.

• 

When using a platter to carry raw meat, uncooked poultry or seafood to the grill, make sure to wash 
the platter thoroughly with soap and hot water before placing cooked foods back on the platter or use 
different platters for raw and cooked foods.

• 

Never use the same utensils when handling raw meat, uncooked poultry or seafood unless you wash 
the utensils thoroughly with soap and hot water.

• 

Never re-use marinade from raw meat or uncooked poultry on foods that have been cooked and are 
ready to be served.

GRILLING TO  PROPER TEMPERATURE:

• 

Use a meat thermometer to be sure food has reached a safe internal temperature. 

• 

The USDA recommends the minimum temperature be reached for the following food items: 

HELPFUL HINTS:

• 

If you pre-cook meat or poultry, do so immediately before grilling.

• 

Never defrost meat at room temperature or on a countertop. 

• 

Refrigerate leftovers within 2 hours of taking food off the grill.

• 

For additional information, please phone the USDA’s toll free Meat & Poultry Hotline at 800-535-4555.

 

Chops  . . . . . . . . . . . . . . . . . . .  145° F (62.8° C)

 

Ground Meat . . . . . . . . . . . . . .  160° F (71° C)

 

Pork . . . . . . . . . . . . . . . . . . . . .  145° F (62.8° C)

 

Poultry . . . . . . . . . . . . . . . . . . .  165° F (73.9° C)

 

Roasts . . . . . . . . . . . . . . . . . . .  145° F (62.8° C)

 

Seafood . . . . . . . . . . . . . . . . . .  145° F (62.8° C)

 

Vegetables . . . . . . . . . . . . . . . .  145° F (62.8° C)

Summary of Contents for 810-6550-S
































































Reviews: