background image

TROUBLE SHOOTING

Problem:

Possible Causes:

1. Check LP cylinder fuel level.
2. Bad electrode spark.

Check to see if the grill will match light.
Electrode or collector may need adjustment.

3. Burner may not be properly seated.
4. Burner may be obstructed.
5. The cylinder valve may be closed.
6. Regulator is not properly seated on cylinder valve.

1. Burner holes may be obstructed. See section on

"Burner Assembly/Maintenance" under Proper Care
and Maintenance.

2. Burner is improperly seated on control valve.
3. Gas connections may be loose.

Leak Check and tighten all connections.

1. Burner is obstructed. See section on

"Burner Assembly/Maintenance" under Proper Care
and Maintenance.

1. Burner holes may be obstructed. See section on

"Burner Assembly/Maintenance" under Proper Care
and Maintenance.

2. Grill is not sufficiently preheated.
3. Burner is improperly seated on control valve.

1. Flow control device has been activated in regulator. 

See Regulator Resetting Procedure under 
Connecting LP Cylinder and Hose/Regulator to Grill.

1. Excess grease build-up causing grease fires.
2. Damaged or faulty regulator.

Replace with factory authorized parts.

3. Cook on a lower temperature setting.

Burner will not light

Fire at control knob

Yellow Flames at burner

Flame blows out on "LOW"

Burner does not get hot enough

Grill is Too Hot

BEFORE STORING YOUR GRILL:

Ensure that the cylinder valve is fully closed.

Clean all surfaces. 

Lightly coat the burners with cooking oil to prevent excess rusting.

If storing the grill indoors, disconnect the LP tank and leave the LP tank OUTDOORS. 

Place a protective cap cover on the LP tank and store the tank outdoors in a well ventilated area out
of direct sunlight.

Clean burner prior to use after storing, at the beginning of grilling season or after a period of one
month not being used. Spiders and insects like to build nests in burner tubes (especially during colder
months). These nests can cause fires in burner tubes or under grill.

If storing the grill outdoors, cover the grill with a grill cover for protection from the weather.

17

Summary of Contents for Pro 8445



































Reviews: