BRILUM S.A.
05-500 Piaseczno, Stara Iwiczna, ul. Słoneczna 116A
www.brilum.pl
www.brilum.pl
ORTO
EN
INSTALLATION AND OPERATING MANUAL
ORTO - LED recessed downlight
Recessed downlight
TECHNICAL DATA
ELUM Sp. z o.o.
ul. Wilanowska 1A, 05-520 Konstancin-Jeziorna, Poland
www.elum24.pl
CAUTION!
1.
Terminal block for current ~230V is not included. An advice from qualified person
is needed for installation.
2. Light sources are not replaceable; once light sources are used up, full luminaire
should be replaced.
3. For proper operation of ORTO luminaire, it is forbidden to cover the luminaire and
LED driver with thermal insulation material!
4.
We reserve the right to apply changes in the construction of the product.
5.
The information included in this document may undergo changes without warning.
6.
Possible changes will be taken into consideration while working with other issues
of the instructions for use or complementary documents.
7.
We take no responsibility for faults resulting from non-compliance with the above
instructions. According to article 568 pt 1 of the Polish Civil Code, the right resulting
from a warranty for physical defects are extinct after the lapse of 2 (two) years after
delivery of the luminaire to the Buyer.
SAFETY AND MAINTENANCE
1.
Installation of the luminaire should be done by the certified and experienced electrician.
Before starting the installation you must absolutely turn off the main power supply,
where the luminaire should be connected to, to avoid accidental voltage connection!
2. Electrical cables must be connected according to the instruction and regulations in
force.
3. To keep the optimal technical parameters of the luminaire the periodical maintenance
should be carried out. Before cleaning the product, disconnect it from power supply.
Ignoring this warning can cause danger of electric shock. The housing of the luminaire
should be cleaned by generally available cleaning supplies and also dried with a soft
cloth. Do not use corrosives chemicals and solvents. Do not use stream of water under
pressure.
This symbol stands for selective collecting of the electrical and electronic equipment,
therefore, this product cannot be treated as other household’s waste. It has to be left
at a special used-equipment collection point. The appropriate dealing with the
collection of used electrical and electronic equipment is crucial, especially if the
equipment includes dangerous components which have a negative influence on the
environment and on the health of people.
Model
ORTO
Power of the luminaire
6W
9W
12W
15W
18W
24W
Supply voltage
220 ÷ 240V AC
Frequency
50/60Hz
Beam angle
113°
Protection rate
IP 20
Protection class
II
LEDs type
SMD
Light colour
warm white / neutral white / daylight
Correlated colour temperature
3000K / 4000K / 6000K
Colour rendering index (CRI)
> 80
LEDs lifespan*
10 000 hours
Luminous flux of the luminaire**
240 lm 495 lm 660 lm 825 lm 1080 lm 1440 lm
Ambient temperature
-20°C ÷ +50°C
Weight
0,118kg 0,154kg 0,209kg 0,250kg 0,299kg 0,467kg
Diameter of mounting holes (mm)
Ø110
Ø130
Ø160
Ø170
Ø210
Ø285
* provided parameter is based on LEDs manufacturer’s data
** parameter is provided with ±5% tolerance margin
DIMENSIONS (mm)
Model
A
B
ORTO, 6W
Ø118
17
ORTO, 9W
Ø145
17
ORTO, 12W
Ø170
17
ORTO, 15W
Ø190
17
ORTO, 18W
Ø220
17
ORTO, 24W
Ø298
17
A
B
CHARACTERISTICS
ORTO are energy - saving LED downlight luminaires, equipped with faultless, high qualit
and very efficient LEDs, SMD type with low power consumption and long lifespan that
allow significant energ saving comparing to traditional luminaires, with the same luminous
parameters. High colour rendering index CRI, is close to natural light - tipical for ecologic
LED lighting - it provides vivid colour rendering.
CONSTRUCTION
Body is made of durable aluminum casting. Aluminum heat sink provides effective heat
dissipation and ensures that LED panel’s temperature will not exceed the standards while
luminaire is turned on. Cover is composed of light guiding plate made of synthetic material
and polystyrene (PS) milky diffuser which provides soft and even dispersed light.
LED driver included in the set with luminaire.
APPLICATION
ORTO luminaires are commonly used as illumination of shop areas, reception halls,
hallways and corridors, banks, hotels as well as residential apartments.
85mm
95mm
110mm
Fig. 1. Cables dimensions.
INSTALLATION
To install the luminaire in suspended ceiling:
1.
Prepare a suitable mounting hole [Fig.2.] - according to the type of luminaire,
the dimensions of mounting holes are provided in the ,,TECHNICAL DATA” table.
2. Connect the LED driver to mains ~230V 50/60Hz [Fig.3.].
3. Connect LED driver to the luminaire [Fig.4.].
4.
Place the luminaire in previously prepared mounting hole and deflect the springs
[Fig.5.].
Fig.2.
Fig.3.
Fig.4.
Fig.5.
L - phase cable
N - neutral cable
