Garden lamps GARDEN LED UPR, DN, HG, P1, P2, UP
ENG
Garden lamps GARDEN LED
Garden lamps are made of high aluminum, thanks to which they prove high resistance to the
weather conditions. Thanks to the installed motion sensor, lamps are automatically connected
only when the lighting is needed (only GARDEL LED UPS). As a lighting source,
LEDSTAR CLASIC bulb with lampholder E27 and power 7W.
Application: outdoor lighting at entrances, terraces.
Supply voltage: 230VAC 50/60Hz.
INSTALLATION
GARDEN LED UP, DN
[1] Unscrew the body by unscrewing the nuts at the base of the lamp.
[2] Drill two holes on the wall and insert expansion plugs ( included in the set)..
[3] Take supply cable through the pass at the base of the lamp.
[4] Fasten the base of the lamp to the wall by two bolts (included in the set).
[5]
[6] Put the LEDSTAR CLASIC bulb into the lampholder.
[7] Turn the lamp to the fastened base.
[8] Put the cover (models UP) or the shade of the lamp (models DN) and screw it by two bolts.
Remove the insulation from the supply cable (about 1cm) and connect it to the connector
terminal (4) accordingly: phase cable (brown or black) to the marked inlet ,,L”, neutral one
(blue) to ,,N” and protection one (yellow-green) to
.
www.brilum24.pl
www.brilum24.pl
BRILUM S.A.
ul. Wilanowska 1A, 05-520 Konstancin-Jeziorna, Poland
GARDEN LED UPR
GARDEN LED DN
GARDEN LED HG
GARDEN LED P1
GARDEN LED P2
GARDEN LED UP
GARDEN LED HG
[1] Unscrew two bolts at the lateral side of the cover of the connector terminal, which is located
at the end of the supply cable.
[2] Drill two holes on the ceiling and insert expansion plugs (included in the set).
[3] Take supply cable through the pass at the base of the lamp.
[4] Fasten the base of the lamp to the ceiling by two bolts (included in the set).
[5]
[6] Put the LEDSTAR CLASIC bulb into lampholder.
[7] Turn the lamp into the fastened base.
[8] Put the shade of the lamp and screw it by two nuts.
Remove the insulation from the supply cable (about 1cm) and connect it to the connector
terminal (4) accordingly: phase cable (brown or black) to the marked inlet ,,L”,
neutral one (blue) to ,,N” and protection one (yellow-green) to
.
GARDEN LED P1, P2
[1] Drill two holes on the stable ground and insert the expansion plugs.
[2] Take supply cable to the body of the connector terminal at the base of the lamp.
[3] Remove the insulation from the supply cable (about 1cm) and connect it to the connector
terminal (4) accordingly: phase cable (brown or black) to the marked inlet ,,L”,
neutral one (blue) to ,,N” and protection one (yellow-green) to
.
[4] Fasten the lamp to the stable ground by two bolts (GARDEN LED P2)
[5] Fasten the lamp on the pole and turn it by three bolts (GARDEN P1)
[6] Put the LEDSTAR CLASIC bulb into lampholder.
[7] Put the shade of the lamp and screw it by two nuts.
GARDEN LED UPR
[1] Unscrew the body by unscrewing the nuts at the base of the lamp.
[2] Drill two holes on the wall and insert expansion plugs (included in the set)..
[3] Take supply cable (1) through the pass (2) at the base of the lamp (3).
[4] Fasten the base of the lamp (3) to the wall by two bolts (included in the set).
[5] Remove the insulation from the supply cable (about 1cm)
and connect it to the connector terminal (4) accordingly:
phase cable (brown or black) to the marked inlet ,,L”,
neutral one (blue) to ,,N” and protection one
(yellow-green) to
. (Fig.2.)
[6] Put the LEDSTAR CLASIC bulb into the lampholder (6).
[7] Fix the lamp to the fastened base (bolt 5).
[6] Put the cover (7) and fix it by two bolts.
10m
1,8
÷
2,5m
230VAC 50/60Hz
CZUJNIK RUCHU
Connect the power supply and keep waiting for about 1 min. so that the motion sensor
becomes stable. During the period of sensor stabilization, the lamp can be switched on
and switched off.After that, the lamp is ready to work.
Glaring time of the lamp (from the moment of detecting the last movement), which is
regulated by knob “TIME” at the range of 10 seconds (utmost left position) to 4 minutes.
Fig.1. Motion detection scope: max 10m at 20°C
Fig.2. Connection of of supply cable
A - black (sensor)
B - brown (bulb)
C - blue ( bulb)
D - yellow-green (grounding)
E - brown (sensor)
F - brown ( phase wire)
G - blue (neutral wire)
0,68kg
GARDEN LED P1
200
345
45
GARDEN LED P2
1,00kg
200
405
150
285
GARDEN LED HG
1,06kg
60
890
235
200
GARDEN LED UP
1,00kg
145
200
350
225
GARDEN LED DN
1,00kg
225
145
350
200
1,22kg
EL-270UPS
GARDEN LED UPR
210
175
370
160
This symbol stands for selective collecting of the electrical and electronic equipment,
therefore, this product cannot be treated as other household’s waste. It has to be left
at a special used-equipment collection point. The appropriate dealing with the
collection of used electrical and electronic equipment is crucial, especially if the
equipment includes dangerous components which have a negative influence on the
environment and on the health of people.
The information included in this document may undergo changes without warning. Possible changes will be
taken into consideration while workingon other issues of the instructions for use or complementary documents.
The manufacturer is not liable for faults resulting from non-compliance with the above instructions.
According to Article 568 § 1 the implied warrantyrights regarding physical defects expir after one year counted
from the day the fixture was delivered to the purchaser.
Installation and operating manual
APPLICATION
DIMENSIONS
CAUTION! Make sure that power is off before installation! Electrical cables must be
connected according to the instructions and regulations in force. It is recommended that
the installation is carried out by a qualified electrician.
Installation on normally
flammable surface.
