background image

9

5. Electrical connection

5.1 Connection diagram for the swimming pool heat pump

XHP 40, XHP 60, XHP 100

IMPORTANT:

 The installation and connection of this device to the power supply can only be provided by 

a person that has the electrical qualifications in accordance with Decree No. 50/1978 Coll. Although the heat 
pump is electrically insulated from the rest of the unit, this fact only prevents the passage of electrical current 
to or from the water in the swimming pool. It is still necessary to earth the unit, to prepend the circuit breaker 
with the current value according to the type of heat pump and current protector with residual current 0.03 A.
Before connecting the heat pump, check whether the electrical mains voltage corresponds to the operating 
voltage of the heat pump.

Compressor 

Fan motor

Four

-way valve 

Electric expansion

valve

Transformer 

OUTPUT3

OUTPUT4

OUTPUT5

RUN/ POWER SUPPLY

brown

brown

red

red

red

red

brown

yellow

yellow/ green

yellow/green

white

white

black

black

blue

blue

orange

GROUND

GROUND

GROUND

GROUND

GROUND

GROUND

yellow/green

blue

blue

blue

black

GROUND

GROUND

GROUND

GROUND

GROUND

GROUND

blue

Ambient temperature sensor 

Cooling coil temperature sensor

Returned coolant temperature sensor 

Heating coil temperature sensor 

Water outlet coil temperature sensor

Water inlet coil temperature sensor 

Remote control

Phase sequence protection 

High voltage switch 

Low voltage switch 

W

ater flow switch 

Remote switch

*Section marked with dotted lines is only in some models.

OUTPUT2

OUTPUT1

SINGLE WATER 
PUMP

POWER SUPPLY 
220

240 V/50 Hz 

EN

Summary of Contents for XHP 100





























Reviews: