Brighter Eye 360 Led User Manual Download Page 3

 

1. Safety Instructions 

 

 

 

Please keep this User Guide for future consultation. If you sell the unit to another user, be 

sure that they also receive this instruction booklet. 

 

Unpack and check carefully there is no transportation damage before using the unit. 

 

Before operating, ensure that the voltage and frequency of power supply match the power 

requirements of the unit. 

 

It’s important to ground the yellow/green conductor to earth in order to a

void electric shock. 

 

The unit is for indoor use only. Use only in a dry location. 

 

The unit must be installed in a location with adequate ventilation, at least 50cm from 

adjacent surfaces. Be sure that no ventilation slots are blocked. 

 

Disconnect main power before replacement or servicing. 

 

Make sure there are no flammable materials close to the unit while operating as it is fire 

hazard. 

 

Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but 

always by taking its base. 

 

Maximum ambient temperature is Ta: 40

. DO NOT operate it where the temperature is 

higher than this Unit surface temperature may reach up to 85

 

DO NOT touch the housing bare-hands during its operation. Turn off the power and allow 

about 15 minutes for the unit to cool down before replacing or serving. 

 

In case of serious operating problem, stop using the unit immediately. Never try to repair 

the unit by yourself. Repairs carried out by unskilled people can lead to damage or 

malfunction. Please contact the nearest authorized technical assistance centre. Always use 

the same type spare parts. 

 

DO NOT touch any wire during operation as high voltage might be causing electric shock. 

 

Warning: 

 

 

To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or 

moisture. 

 

DO NOT open the unit within five minutes after switching off. 

 

The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly 

damaged. 

 

Caution: 

 

There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any 

repairs by yourself. If your unit requires service, please contact your nearest dealer. 

 

 

 

Summary of Contents for Eye 360 Led












Reviews: