manualshive.com logo in svg

Brigade Sidescan SSP-6000W, Installation & Operation Manual, Page: 11 / 29

Share
Download
Brigade Sidescan SSP-6000W Installation & Operation Manual Download Page 11

20

21

4.3   Configuration Tool Software Installatio

n

Agree to the license agreement and 

click “Next”.

Select the installation folder and click 

“Next”.

Confirm installation then click “Next”.

Installation complete - click “Close”.

A shortcut will appear on the desktop.

4.4   Using the Configuration Tool Software
4.4.1  Installation File, Vehicle Configuration File and Sensor Configuration File

4 

Configuration Software

Download the installer file from our 

website. Run the downloaded installer 

file on the device that will be used for 

the installation. The setup wizard will 

appear. Select “Next”.

The Sidescan

®

Predict configuration software uses an individual installation file (.bif) for each 

installation. This is linked to the unique serial number of the algorithm ECU. A different 

installation 

file must be used for each installation. This file will save automatically as the 

installation progresses.

When you open the software the first window will provide the options to create new or use existing 

installation. To create a new installation file, click “New Installation”.  

To return to an existing installation, click “Open an Existing Installation”.

Summary of Contents for Sidescan SSP-6000W






























Reviews:

No comments