background image

— 22 —

Main conditions of long service life is right and careful servicing. Avoid excessive increasing of pressure in the board, especially from heating by the sun rays.

After exploitation take off sand and dirt from boat surface, and carefully dry it.

Avoid the water getting into the chambers. If a fuel or an oil gets to the boat surface it is necessary to wash the soiling place by soap water as soon as possible

and dry.

Pay attention to the condition of bottom surfaces. If it's cover is destroyed it is necessary to dry this element and restore the defend cover.

After season prepare the boat to winter keeping. Clean boat surface from sand and dirt and make the necessary repairs, if damages take place. If it is possible,

keep the boat in the open and slightly pumped state in air temperature 0-25°C.  The boat must be protected from the sun rays.

Insignificant boat repairing (eliminating the board punctures or cuts) you may carry out by yourself. In this case use the coated fabric  and glue set for repair from

the complete set.
Independent performance of any complex repair associated with considerable damages to the board, partitions and seams is not recommended. In such
cases, apply to your dealer.

MAINTENANCE.

Dear owner,

We thank your for your purchase and do hope that you will have a great fun of it. However, to make your joy and pleasure complete,
we would request you to read  carefully and observe the   directions and recommendations  specified below.

OPERATING REGULATIONS.

Storage of the boat with temperature variations from -30°C to +45°C may be allowed for not  longer than 1 month.
In case the boat has being stored or transported at a temperature bellow 0°C, it must be held at a temperature

above +15°C for at least 1 hour before be unpacked and unfolded.

For small repair boat tube use the coated fabric  and glue set from the complete set.

IT IS STRICTLY FORBIDDEN to handle the boat in the state of intoxication and without individual rescue

means being used (life-saving belts, jackets, etc.)

IT IS FORBIDDEN to use an outboard engine of power exceeding the maximum allowable value

Summary of Contents for F400H

































Reviews: