Brevi 536, Instructions For Use Manual

Page: 23 / 28

23
To release the Isofix connectors
1. Slide upwards the force leg pressing the
adjustment push button (Pic. 9-A ).
2. Move the seat forward by pressing the side le -
vers and pulling it forward (Pic.9-B).
3. Press the pushbutton on the articulation of the
force leg as shown (Pic.9-C), to release the Iso-
fix connectors. WARNING: Only if both
indicators are red it is possible to re-
move the child seat from the vehicle.
Method B: Installation of the child seat
using the safety seat belt and the force
leg
Checking the vehicle seat belt
•
Installation of this child seat in the vehicle is only
suitable if the vehicle is equipped with 3-point
seat belts with retractor, approved to UN/ECE
Regulation No.16 or other equivalent standards.
•
The stability of the car seat can be affected by the
position of the vehicle seatbelt buckle.
•
The stability of the car seat can be affected by
the position of the vehicle seatbelt buckle; if it
happens to be positioned as in Pic. 10, this child
seat is not suitable for use with your belt or your
vehicle.
1. Rotate the support leg, so that it is in an upright
position (Pic.11-A).
2. Hold the seat and pull out the force leg to re-
tract the two connectors in the child seat base
(Pic.11-B).
3. Place the child seat on the appropriate vehicle
seat, facing forward (Pic. 12).
4. Grip the reclining lever (Pic. 13) and pull the seat
forward until it’s totally reclined, to operate more
easily.
5. Pull to open the locking lever of the red belt
clamp on the opposite side of the vehicle seat
buckle (Pic.14).
6. Pull out the car safety seat belt and place
it between the backrest and the seat frame
(Pic.15).
7. Slot the buckle tongue in the car seat buckle (Pic.
16) until it clicks in.
8. Pass the lap section (Pic.17) in the lower red belt
guides on both sides of the seat frame.
9. Insert the diagonal seat belt section through the
red belt clamp (Pic. 18).
Warning: Ensure
that the belt has not been twisted
(Pic. 19);
10. Press the child seat firmly against the vehicle
seat and back of the vehicle seat and at the same
time, pull tightly upwards the diagonal section of
the seat belt through the belt clamp (Pic. 20) until
there is no slack; then close the belt clamp (Pic.
21). Caution! The diagonal seat belt
section (14-B) may be clamped using
only the belt clamp on the opposite
side of the vehicle seat buckle;
11. Adjust the height of the support leg by pressing
the pushbutton located at its back (Pic. 22) and
slide down the lower section until it reaches the
floor of the vehicle.
12. Release the button and check that the support
leg is locked in position and its bottom well in
contact with the vehicle’s floor. Important:
when adjusting the support leg, make
sure that the base of the seat always
remains in contact with the seat (Pic.
23) and not elevated.
13. You may now use the child seat at your chosen
position, by using the reclining lever (Pig. 24).
Removing the child seat from the vehi-
cle
1. Grip the reclining lever (Pic. 13) and pull the seat
forward to the reclined position.
2. Open the clamp in which the seat belt is enga-
ged.
3. Release the vehicle seat belt from its buckle.
4. Take the lap seat belt section off the red belt gui-
des and withdraw the vehicle seat belt to remove
the child seat from your vehicle.
III. Securing the child in the seat
1. Press the red button on the buckle to unlock it
(Pic. 25).
536-03-160429-00. istruzioni AXO Isofix ZH-EN_A6 .indd 23 18/05/2016 11.51.59