-Gateway GWY 433
The LAN gateway allows comfortable control of all SteckerChecker-compatible
433MHz wireless actuators via an iPhone, iPad or Android smartphone/tablet by
integrating into your home network.
User manual Home Automation Gateway GWY 433
Requirements
To operate the gateway, you require an Android or iOS device and a WLAN router
(in DHCP mode) with a free RJ45 ethernet network connection.
First steps
After removing the packaging, only a few steps are needed to start using the
system. In the fi rst steps, we assume that you use a WLAN router with activated
DHCP in your home network (which is typically the case). If that isn‘t the case,
you have to activate DHCP on your WLAN router.
Screw on the antenna
Screw on the 433MHz antenna
to the provided socket
on the LAN gateway
. It can be rotated and angled so it can be aligned in any installation position.
GB
Connecting the LAN gateway
Connect the gateway
to your WLAN router
. using the provided
network cable
. If the router is not switched on yet, switch it on now
and wait until it is operationally ready.
LAN
Connect the gateway
with the provided power supply
; then the LAN gateway
will search for a few seconds for a free IP address on the network. Alternatively,
the LAN gateway can also be supplied with power via a 5V USB connection (500mA).
This can be done e.g. via a USB charger, PC, laptop or USB outlet on the WLAN router.
Operational readiness
•
The blue LED will blink from the time it is plugged in until it is assigned an
IP address from the DHCP router. If this process is successful, it goes out.
If the LAN gateway is not assigned an IP address, the blue LED will continuously
blink in short intervals.
•
When sending the command to switch on or off a wireless actuator,
the blue LED will light up once.
•
The orange LED on the network outlet
will remain lit and indicates that the
WLAN router has been recognised as the remote station.
•
During a data transfer, the green LED on the network outlet
will light up briefl y.
•
The blue LED is lit permanently ¬ To re-synchronization press
the reset button
6 seconds during operation.
•
Restart/reset the gateway ¬ Press the reset button
6 seconds.
Download the SteckerChecker app
For comfortably controlling the wireless receiver from the gateway, fi rst,
the SteckerChecker app must be installed on the iPhone, iPad, Android smartphone
or Android tablet. For information about the SteckerChecker and the download
of the app go online to www.steckerchecker.de
Installation and starting the app
Install and start the SteckerChecker app.
All important steps and settings in the app can be found in the SteckerChecker
tutorials: http://www.steckerchecker.de/tutorials.
Technical data
Transmission frequency:
433,92 MHz
Certifi cation:
The system has a general certifi cation (BZT)
and does not require fees or registration
Radio signal range:
max. 25 m
Ambient temperature:
0°C to 35°C
Storage temperature:
-40°C to 70°C
Supply voltage power supply:
Input:
230V~, 50Hz
Output:
5Vdc, 500mA
CE-compliant:
SteckerChecker switching function
Hazardous situations can arise when switching electrical devices and consumers
on and off without supervision. Use the switching function only for outlets,
switches and connected devices that are expressly released for this purpose
by the manufacturer and which do not pose a danger when switched on.
If in doubt, please ask the respective manufacturer fi rst.
In addition, also be aware that SteckerChecker cannot guarantee that a required
switching process will actually be carried out because of the technologies used.
SteckerChecker cannot control the system-based status of connected devices.
Therefore, do not switch electrical devices and consumers that pose a danger or
may develop into a risk or which rely on reliable switching unless you have visual
contact.
You are liable for risks resulting from improper use of the switching function.
Disposal
Do not throw electronic devices away with the house rubbish!
In accordance with European Guideline 2002 / 96 / EC for electronic
and old electronic devices, used electronic devices, illuminants and
batteries must be collected separately and disposed of in an environmentally
sound recyclable manner. You can learn more about the disposal options for
the used devices at your municipal or city administration.
Conformity Declaration
The CE marking was attached in compliance with
the following European guidelines:
1999/5/EG R&TTE directive
2006/95/EG Low voltage directive
2004/108/EG EMV directive
2011/65/EU (RoHS II)
The conformity declaration can be found at the following link:
www.brennenstuhl.com/konformitaetserklaerung/ke_1294100.pdf
Manufacturer:
Hugo Brennenstuhl GmbH & Co. KG
Seestr. 1-3 · 72074 Tübingen · Germany
www.brennenstuhl.com
Copyright notice
iOS, iPhone, iPad, Android and SteckerChecker are registered brands or registered
trademarks of their respective owners and may not be expressly labelled.
Firmware Update
(The fi rmware should be up-to-date at the delivery!)
1. Disconnect the gateway
from the network and connect the USB cable
to a free USB port on your computer / laptop.
2. Download the latest fi rmware from our website www.brennenstuhl.com.
3. Run the fi le „FirmwareUpdater.exe“ and follow the installation instructions.
4. Start the update.
Safety Instructions
Read the operating instructions and safety
instructions carefully.
Avoid a risk to life
due to electric shock!
•
Never open the device, in particular, the power supply yourself. Only have
the necessary repairs performed by the service department or a qualifi ed
electrician.
•
Only use the power supply in closed rooms. They are not suitable
for outdoor use.
•
These instructions are a component of the device. They must be included
when passing on the device to a third party.
•
Avoid moisture and extreme temperatures.
Home Automation
Gateway GWY 433
User manual
Scope of delivery
1 x Gateway GWY 433
1 x USB power supply (500mA)
1 x Antenna (SMA)
1 x USB cabel (1.8 m)
1 x Ethernet cabel (1.0 m)
Gateway GWY 433
Antenna (433MHz)
Programming / reset button
Antenna socket
Mini-USB socket
Network socket
Router
Network cable
USB cabel
Power supply
