Bremax NRC-502 User Manual Download Page 2

Page: 2 / 6

.6.

1.1 Double click learning software icon and run the software.

1.2 Click on

Start to learn

button on the webpage right below.

Follow the steps below to learn the RC codes from ordinary
remote control after finishing the steps of preparation.

Operation

Step 1

Install Learning software

1. Visit our company website at

Find

Service & Support

and select

Download

2. Find your model and click

Download

. For example, if

your model is NRC-502 internet powered URC, please find

NRC-502 Learning Software

first and then click

Download

3. Double click NRC-502 Learning Software.exe Follow

the on-screen instructions to complete the installation.

Step 2

Complete Learning Operation

Be patient during the operation because the code for a

single button has to be recorded at a time. Please do it one by
one. Here below is an example of how to learn an ordinary TV
RC:

For example, the steps of learning

Power

button from TV RC to

button on URC are shown as

follows: (Fig 10)

www.bremax.com.

1. Learn single button:

Inter net

USB

As indicated in

, connect Bremax

with one online

PC via USB cable provided. Connect the smaller plug of
the cable to

and the bigger one to the USB port on

your computer.

Fig 9

URC

Fig 9

Power Button

Button

Power section

Learned to

NRC-502

TV RC

Fig 10

.4.

+ +

- -

.5.

Getting Your Codes

NRC-502 is an easy-to-program and easy-to-use remote
control. You have many ways to get your codes for the
particular device and brand. Firstly, you can setup the remote
using the code for your brand of device, from the code tables
(on separate sheet), or download needed RC codes on the
internet. Moreover, NRC-502 has powerful learning ability.
You can learn RC codes from your original remote control
directly, or learn RC codes via USB connection with PC, to
control your devices. Specifically, there are two learning
modes:

Direct Learning Mode and Online Learning Mode

(Based on PC).

Fig 4

button

1. Manually turn on your TV set
to be controlled and search for
the code number for your TV
brand from code tables (on
separate sheet).

2. Press and hold the

button

(

over 5 seconds

) until the red

indicator blinks 3 times and
stays on. Then release the

button.

3. Enter the 4 digit code from
the code tables (on the separate
sheet).If your brand has more
than one code listed, begin with
the first code. When a valid code
is entered, the red indicator
blinks 3 times and turns off. For
an invalid code, the red indicator
flashes.

4. With your TV on, press

CH +

button. If the device responds,
no further programming is
required. If some buttons can not
operate your device, try one of
the other codes for your brand.

5. Repeat steps 1 to 4 to setup
the RC codes of other devices
(CBL/SAT, DVD/VCD, AMP).

Direct Code Entry

Here below is an example of how to setup the TV section of
URC using the code tables.

PHILIPS

Brand

Code

0001,0013,0030,0041,

0061,0069,0074,0088,

0129,0144,0154

0001

PHILIPS

Enter your codes here for easy reference later.

Direct Learning Mode

Here below is an example of how to learn

Power

button of an

ordinary TV RC.

1. Press and hold the

button (

over 2 seconds

) until the

red indicator turns on. Then release the button.(Fig 7,Finger 1)

2. Press the

button on Power section of BREMAX

URC that you want to learn, the red indicator blinks and then
stay on.(Fig7,Finger 2)

3. Place TV RC and

head-to-head (within

5-20cm) as shown in Fig 8.

BREMAX URC

TV CODE

DVD CODE

CBL/SAT CODE

AMP CODE

Fig 6

Fig 7

5~20 CM

NRC-502

TV RC

Fig 8

Press and hold the Power button on your original

remote until the red indicator blinks 3 times quickly and stays
on. If there is a learning problem, the indicator blinks 3 times
slowly and stays on. If this happens, repeat Step 2 to 4.

5. Repeat Step 2 to 4 for other buttons you want to learn.

6. Press and release the

button when all desired remot-

e commands are learnt. Code Learning is now complete.

Note: URC will quit the learning mode within 8 seconds
if no signal from the original remote is received under
Direct Learning Mode. If this happens, please try again.

Online Learning Mode (Based on PC)

Prepare a computer and connect it to the Internet. The m-
inimum recommended system configuration is:

Inter Pentium III processor or higher

USB1.1 (Universal Serial Bus) or higher

20M free hard disk space

Windows98SE/Me/2000/XP operating system or

higher

Monitor resolution of 1024 768 or higher

Fig 5