background image

6

Installation 

 

 

WARNING: 

To reduce the risk of fire, electric shock, or

personal injury, mount the fan to an outlet box marked
acceptable for fan support. An outlet box commonly used  for
the support of lighting fixtures may not be acceptable for fan
support and may need to be replaced. If in doubt, consult  a
qualified electrician.     

MOUNTING OPTIONS

1

1

1

2

If your ceiling fan does not have an existing UL-listed mounting 
box, then install one using the following instructions: 

      Disconnect the power by removing the fuses or  turning

off the circuit breakers. 

     Secure the outlet box (1)  (not included) directly to the

building structure. Use appropriate fasteners  and
materials (not included). The outlet box and its bracing
must be able to fully support the weight of the moving
fan (at least 35 lbs.). Do not use a plastic outlet box.    

The illustrations to the right show three different ways to
mount the outlet box (not included). 

To hang your fan where there is an existing fixture but  no
ceiling joist, you may need an installation  hanger bar (2) 
(not included), as shown. 

Summary of Contents for AURORA BF9775L52-BN

















Reviews: