BRECHTEL STAP 9406 Instrument Manual Download Page 33 | Manualshive

Page: 33 / 48

BRECHTEL STAP 9406 Instrument Manual Download Page 33

7

Operating the STAP

Diagnostics Menu

psvolts: (power supply voltage)
err_rpt: (error report numbers)

Calibration Values Menu

ﬂow_c2: (ﬂow x2 coefficient)
ﬂow_c1: (ﬂow x coefficient)
ﬂow_c0: (ﬂow offset coefficient)
ﬂwcalt: (temperature during calibration)
prsslop: (slope for pressure reading)
prsoffs: (offset for pressure reading)
vltslop: (slope for power supply voltage reading)
vltoffs: (offset of power supply voltage reading)

Raw Readings Menu

ﬂw_raw: (raw LFE ﬂow reading (0-4095) )
prs_raw: (raw pressure reading (0-4095) )
vlt_raw: (raw power supply reading (0-4095) )

Manufacture Info Menu

The Manufacture Info menu displays the following lines:

version: (ﬁrmware version)
ser_num: (serial number)
mfgyear: (mfg year)
mfg_mon: (mfg month)
mfg_day: (mfg day)

All settings and calibration values are saved to the on board EEPROM memory when
users return to ”READINGS” mode from ”DEFAULT SETTINGS” mode. If changes are
made without returning to ”READINGS” mode, e.g. powering off while in ”DEFAULT
SETTINGS” mode, the new settings will not be remembered.

83-00036-01A

STAP 9406

Page 32 of 46

«
...
31
32
33
34
35
...
»

Summary of Contents for STAP 9406

















































Reviews:

No comments