manualshive.com logo in svg

Bray FLOW-TEK 19 Series, Installation, Operation And Maintenance Manual, Page: 30 / 39

Share
Download
Bray FLOW-TEK 19 Series Installation, Operation And Maintenance Manual Download Page 30

FLOW-TEK SERIES 19 SEGMENTED BALL VALVE

Installation, Operation, and Maintenance Manual

30 of 39

© 2021 BRAY INTERNATIONAL, INC. ALL RIGHTS RESERVED. BRAY.COM   The Information 

contained herein shall not be copied, transferred, conveyed, or displayed in any manner that would 

violate its proprietary nature without the express written permission of Bray International, Inc.

17.0 

DISASSEMBLY AND INSPECTION  

(S19 ASME 600)

NOTICE

These instructions apply to resilient seat and metal seat designs.

17.1

Dismantling the Valve

17.1.2 The valve must be removed from the pipeline. (Refer to section 

Removing Valve From Pipeline

.)

17.1.3 Neutralize all energy sources (electrical, pressure and 

mechanical).

17.1.4 Rotate the valve to the closed position.

17.1.5 Remove actuator assembly. (Refer to section 

Actuator Removal 

and Remounting

.)

17.1.6 Remove the gland retainer from the stem by dismantling gland 

nuts and washers. (Removing the studs is not necessary.)

17.1.7 Remove the post cover from the end post by dismantling post 

cover nuts and washers. Carefully insert a screwdriver between 
the post cover and the body to remove the post cover, gasket, 
and end post thrust washer.

17.1.8 Using a punch and mallet, drive the stem pin into the center of 

the stem until the outward end of the pin clears the segment. Be 
careful not to damage the stem.  

NOTE

: The pin can be removed from the stem by driving it out of 

the through-holes with a mallet and punch once the segment has 
been removed.

17.1.9 Remove the end post.  

NOTE

: Inserting a bolt in the jack screw hole (tapped in the post) 

will help in removing the post.

17.1.10 Remove the stem, along with retaining ring, gland ring, stem seal 

kit, packing spacer, thrust washer, and split ring by pulling out 
through packing box side.

CAUTION

Take special care to not damage the splined end of stem during 
disassembly.

17.1.11 Remove the segment by rotating the segment inside the body so 

the non-splined end of the segment is toward the downstream 
port of the body. Remove the segment straight out of the body.

CAUTION

Be extremely careful not to gall or scratch the sealing surface of 
the segment when removing it from body. Scratches may later 
cause excessive leakage and seal wear

17.1.12 Remove the bearings and clean the bearing housing spaces.

17.1.13 Remove the seat. (Refer to section 

Seat Replacement

.)

Figure 15:

 Dismantling the valve.

Summary of Contents for FLOW-TEK 19 Series








































Reviews:

No comments