Brave VH0934 Owner / Operator Use And Care Manual Download Page 13 | Manualshive

Page: 13 / 48

background image

Assembly Procedure

Some components are very heavy
and can be damaged if mishan-
dled. Also, to help prevent per-
sonal injury, it is strongly recom-
mended that two (2) people work
together to uncrate and assemble
the log splitter.

1

.

Remove and read all instructions and
safety recommendations before
assembling or operating this log split-
ter.

2

. Before removing the base unit from the

pallet, remove the tongue and front leg
assembly.

3

. Install the tongue and front leg assembly

to the base unit using two 1/2-13 x 3-1/2
inch long hex head bolts, lockwashers,
and nuts. Tighten the nuts securely. Roll
the tongue/base unit off the pallet and
lower the front leg and lock it into position.

CAUTION

815-672-8861

11

Brave Products, Inc.

«
...
11
12
13
14
15
...
»

Summary of Contents for VH0934

















































Reviews:

No comments

Related manuals for VH0934

Brand: CYP Pages: 16

Brand: Brave Pages: 72

DK2 POWER OPS240

Brand: Kohler Pages: 17

Brand: Yardworks Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands