The following section details procedures for checking your log splitter, should you
encounter a malfunction. Brave Products, Inc. recommends that you do not attempt to
make repairs to the log splitter. In the long run, it is better to take your log splitter to a
servicing lawn and garden dealer for repairs.
Problem:
When the control handle is pushed forward (extend), the pusher plate does
not move.
1
. Check the hydraulic tank to make sure the oil level is visible in the bottom
of the fill elbow.
2
. Remove the pump from the engine flange. Check the coupler, making
sure the drive keys are in place and there is no damage to the urethane
spider.
3
. Disconnect the pusher plate from the cylinder. Grasp the hydraulic cylin-
der shaft and try to pull it out. If the rod comes out easily, you will need to
rebuild or replace the cylinder.
4
. Once you have determined that the engine-to-pump coupler is intact and
the cylinder is in good condition, you will need to replace the pump.
Problem:
The engine stalls when the pusher plate engages the wood.
1
. The engine may not be properly adjusted. Take the engine to a service
center for repair and/or adjustment.
2
. If all engine settings are correct, replace the pump.
Problem:
The pusher plate moves slowly, but will split wood.
1
. Check the oil level in the hydraulic tank and fill if necessary.
2
. Check the high-pressure hose, fittings, and valve openings for dirt and
debris that may have obstructed the openings.
3
. If the ram speed is still slow, replace the pump.
Problem:
The ram will not automatically retract.
1
. Check the slide rail or pusher plate for damage.
2
. Push the valve handle to the retract position. If the handle will not stay in
this position, contact the factory.
Problem:
Oil squirts from the fill plug during operation.
1
. The oil tank may be over-filled. Drain oil to the bottom of the fill elbow.
2
. The log splitter is not level. Make sure the log splitter is on level ground.
Mechanical Specifications
Slide Rail . . . . . . . . . . . . . . . . . . . . . . . 4 x 4 inch, reinforced, heavy-duty, steel tube
Wedge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . High carbon steel, 3/4” inch thick
Force/Tonnage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 tons
Cylinder Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 inches
Log Opening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 inch maximum
Engine . . . . . . . . . . . . . . . . . . . . . 3.5 HP horizontal shaft engine (Briggs & Stratton)
Hydraulic Specifications
Cylinder Size . . . . . . . . . . . . . 3 x 18 inch, trunnion mount cylinder with 1.25 inch rod
Hydraulic System Capacity (including cylinder, tank, hoses, and filter) . . . 1.5 gallons
Safety Release Control Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . Detent, auto return
Gear Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . single-stage, 2.7 GPM
Shipping Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148 lbs.
Operating Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138 lbs.
Hydraulic Oil Specifications (non foaming)
Tractor Hydraulic Oil
For extremely cold weather conditions . . . . . . . . . . . . . . . . . . . . . . . . . . SAE 10W
For extremely warm weather conditions . . . . . . . . . . . . . . . . . . . . . . . . . SAE 30W
Transmission Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dextron Ill
Important Notice
DO NOT mix tractor hydraulic oil with transmission fluid. Use one or the other.
Brave Products, Inc.
22
800-350-8739
800-350-8739
23
Brave Products, Inc.
Specifications
Troubleshooting
Summary of Contents for Brave EZ Split PCLS04
Page 34: ......
