background image

Equipment storage and maintenance

After care

• 

Store the restraint safely off the floor to avoid damage and ensure that it cannot 

become a projectile in an accident. This can be achieved by using a wall mounted 

storage bag such as SLR111.

•  Regularly inspect the BraunAbility Kit for damage, wear or malfunction. If any 

problems are identified replace it immediately.

•  When not in use, keep loose occupant webbing ends connected to their 

corresponding buckle sleeves, etc, to prevent them from becoming trip hazards 

and from flailing around when the vehicle is in motion.

•  All webbings and components can be cleaned as necessary, but care should be 

taken to prevent contamination of the webbings with polishes, oils and chemicals.

•  To clean the straps use warm soapy water and a clean soft cloth. Rinse with clear 

water and allow to air dry. To disinfect, use a mild spray disinfectant and do not use 

products containing bleach. 

Important: when cleaning or disinfecting, do not 

immerse buckles, karabiner fittings in the disinfectant or water.

•  If the vehicle is involved in an accident when any restraints are deployed, 

remove them from service and replace immediately. If in doubt please contact 

BraunAbility.

16

KIT9, KIT10, KIT11

Summary of Contents for KIT10





















Reviews: