31
Clean&Charge Station
models 5090cc/5070cc/5050cc only
The Clean&Charge Station has been developed for
cleaning, charging, lubricating, disinfecting and
storing your Braun shaver.
12 Station power socket
13 Lift button for cartridge exchange
14 Station-to-shaver
contacts
15 Clean&Charge Station display
15a Status light
16 Start
button
17 Cleaning
cartridge
Installing the Clean&Charge Station
(see fig. D)
•
Remove the protection foil from the Clean&Charge
Station display.
•
Using the special cord set (10), connect the
station power socket (12) to an electrical outlet.
•
Press the lift button (13) at the rear side of the
Clean&Charge Station to lift up the housing.
•
Hold the cleaning cartridge (17) down on a flat,
stable surface (e.g. table).
•
Carefully remove the lid from the cartridge.
•
Slide the cartridge from the rear side into the base
of the station until it snaps into place.
•
Slowly close the housing by pushing it down until
it locks.
Charging the shaver in the Clean&Charge Station
(see fig. D)
Insert the shaver head down into the cleaning station.
Important: The shaver needs to be dry and free
from any foam or soap residue!
The contacts (7) on the back of the shaver need to
align with the contacts (14) in the station. Push the
shaver in the correct position.
A beep sound confirms that the shaver sits properly
in the station. Charging will start automatically.
Model 5090cc: The Clean&Charge Station analyzes
the hygiene status. The status is shown by the
cleaning program indicators in the Clean&Charge
Station display (15) more details see chapter
«Cleaning programs» below.
Cleaning the shaver
(see fig. D)
When the cleaning indicator
lights up in the shaver
display, insert the shaver into the Clean&Charge
Station, upside down and with the front showing (with
released head lock/contact alignment/beep sound).
Cleaning programs
5090cc: The hygiene status will be analyzed and one
of the following program indicators will light up.
short economical cleaning
normal level of cleaning
high intensive cleaning
5070cc/5050cc: One standard cleaning program
included.
Start automatic cleaning
Start the cleaning process by pressing the start
button (16). If status light (15a) does not shine
(Clean&Charge Station switches to stand-by after
ca. 10 minutes), press start button twice. Otherwise
cleaning will not start.
For best shaving results,
we recommend cleaning after each shave.
Each cleaning program consists of several cycles,
where cleaning fluid is flushed through the shaver
head. Depending on your Clean&Charge Station
model and/or program selected, the cleaning time
takes up to 3 minutes. During this time the status light
blinks. Leave the shaver in the station for drying.
It takes several hours until remaining moisture
evaporates depending on the climatic conditions.
Afterwards the shaver is ready for use.
After completing the cleaning and charging proce-
dure, all indicators turn off.
Removing the shaver from the Clean&Charge
Station
(see fig. E)
Hold the Clean&Charge Station with one hand and
tilt the shaver slightly to the front to release it.
Cleaning Cartridge / Replacement
(see fig. F)
When the level indicator
lights up permanently
red, the remaining fluid in the cartridge is sufficient
for about 3 more cycles. When the level indicator
blinks red, the cartridge needs to be replaced -
(about every 4 weeks when used daily.)
After having pressed the lift button (13) to open the
housing, wait for a few seconds before removing
the used cartridge to avoid any dripping. Before
discarding the used cartridge, make sure to close
the openings using the lid of the new cartridge,
since the used cartridge will contain contaminated
cleaning solution.
The hygienic cleaning cartridge contains ethanol,
which once opened will naturally evaporate slowly
into the surrounding air. Each cartridge, if not used
daily, should be replaced after approximately
8 weeks to ensure optimal disinfection.
The cleaning cartridge also contains lubricants for
the shaving system, which may leave residual marks
on the outer foil frame and the cleaning chamber
of the Clean&Charge Station. These marks can be
removed easily by wiping gently with a damp cloth.
90633616_5090cc_MC_Japan.indd 31
90633616_5090cc_MC_Japan.indd 31
26.10.15 09:16
26.10.15 09:16
CSS APPROVED Effective Date 29Oct2015 GMT - Printed 24Nov2015 Page 31 of 36
