46
7
Mark with a pencil the position for the 4 final fixing screws
T
and
R
.
8
Remove the hood and bore where marked (4 x Ø 8 mm).
9
Insert the wall plugs and 2 screws in the upper holes, screw
in partially, the screws will stand as additional hooking
points.
10
Hook back the hood on the wall.
11
Tighten the 2 upper screws definitively and screw in the 2
lower screws.
12
Connect a pipe (pipe and clips for fixing not supplied, to be
purchased) for fume discharge to the connecting ring
placed above the suction motor unit. The other end of the
pipe must be connected to a fume ejecting device towards
the outside in case the hood is used in suction version.
13
In case the hood is to be used in filter version, fix the
deflector to the chimney support stirrup and connect the
other end of the pipe to the connecting ring placed on the
deflector.
14
Connect to the power supply.
15
Slide the lower section of the chimney up to complete
covering of the suction group to insert it into the special
housing above the hood.
16
Lift the upper chimney and fix it by 2 screws to the chimney
support stirrup.
Reinstall the grease filter.
Operation
The hood is fitted with a control panel with aspiration speed
selection control and a light switch to control cooking area lights.
Use the high suction speed in cases of concentrated kitchen
vapours. It is recommended that the cooker hood suction is
switched on for 5 minutes prior to cooking and to leave in
operation during cooking and for another 15 minutes
approximately after terminating cooking.
Maintenance
ATTENTION!
Before performing any maintenance operation,
isolate the hood from the electrical supply by switching off at the
connector and removing the connector fuse.
Or if the appliance has been connected through a plug and
socket, then the plug must be removed from the socket.
Cleaning
The cooker hood should be cleaned regularly (at least with the
same frequency with which you carry out maintenance of the fat
filters) internally and externally. Clean using
ONLY
the cloth
dampened with neutral liquid detergent.
DO NOT CLEAN WITH
TOOLS OR INSTRUMENTS
. Do not use abrasive products.
DO
NOT USE ALCOHOL!
Warning!
Failure to carry out the basic cleaning
recommendations of the cooker hood and replacement of the
filters may cause fire risks.
Therefore, we recommend observing these instructions.
The manufacturer declines all responsibility for any damage to
the motor or any fire damage linked to inappropriate
maintenance or failure to observe the above safety
recommendations.
Grease filter
Traps cooking grease particles.
The grease filter
must be cleaned once a month using non
aggressive detergents, either by hand or in the dishwasher,
which must be set to a low temperature and a short cycle.
When washed in a dishwasher, the grease filter may discolour
slightly, but this does not affect its filtering capacity.
To remove the grease filter, pull the spring release handle.
Fig. 1
Charcoal filter (filter version only)
Fig. 2
It absorbs unpleasant odours caused by cooking.
The saturation of the
charcoal filter
occurs after more or less
prolonged use, depending on the type of cooking and the
regularity of cleaning of the grease filter.
In any case it is necessary to replace the cartridge at least
every four mounths.
The charcoal filter may NOT be washed or regenerated.
Remove the grease filters.
Fit the charcoalfilters over the motor.
Align the
pins R
on the cowl with the
slots S
, then turn the
filter clockwise until it locks in place.
Reverse the above procedure to remove the charcoal filters.
Refit the grease filters.
CLEANING AND UPKEEP OF YOUR APPLIANCE
To keep your appliance in good working order, we
recommend that you use
Clearit
household products.
Professional expertise for the
general public
Clearit
offers you professional products and adapted solutions
for the daily upkeep of your household and kitchen
appliances.
You may find them in conventional retail outlets, along with a
complete line of by-products and consumables.
Replacing lamps
Fig. 1
Disconnect the appliance from the electricity.
Warning!
Prior to touching the light bulbs ensure they are
cooled down.
Replace the old light bulb with the one of the same type as
specified in the feature label or near the light lamp on the
hood.
Remove cover
A
to access the lamp housing
A
.
If the lights do not work, make sure that the lamps are fitted
properly into their housings before you call for technical
assistance.
