manualshive.com logo in svg

BrandMotion SUTV-1040, Installation Instructions Manual

Share
Download
BrandMotion SUTV-1040 Installation Instructions Manual Download Page 12

                                                                                                                                          

   

 

 
 
 

 
 

SUTV-1040 3-12-2018 

Page 12 of 12 

Side View Camera Wiring:

 Each Side View Camera needs 12-volt accessory power and Chassis ground from 

a clean non-painted surface. Also needs the composite video output cable ran to Video inputs on monitor. (1-
4). Can be hooked up to desired orientation on video screen. All outside connections please use supplied heat 
shrink as to not VOID WARRANTY.  

 

 

 
 

Front & Rear Camera wiring:

 Both Cameras needs 12-volt accessory power and Chassis ground from a 

clean non-painted surface. Also needs the composite video output cable ran to Video inputs on monitor. (1-4). 
Can be hooked up to desired orientation on video screen. All outside connections please use supplied heat 
shrink as to not VOID WARRANTY.  

 

Summary of Contents for SUTV-1040















Reviews:

No comments

Brands by name

Popular brands

Load more brands