Bradford White RG275H10N Manual Download Page 25

 

25 

Maintenance continued- 

 

5.  Annually remove the inner door and main burner assembly to clean orifices and 

related parts of any dirt or other foreign material. Inspect the burner ports for 
obstructions or debris and clean with a wire brush as needed. Wire brush and/or 
vacuum clean the combustion chamber as needed to remove scale deposits and 
debris. 

NOTE:

 It is imperative for proper operation of the water heater that the 

inner door be replaced in the original location. 

 

 

 

6.  At least once a year, check the combination temperature and pressure relief valve 

to ensure that the valve has not become encrusted with lime. Lift the lever at the 
lever at the top of the valve several times until the valve seats properly without 
leaking and operates freely. 

 

7. 

Monthly drain off a gallon of water to remove silt and sediment. 

 

 

 

8.  If the combination temperature and pressure relief valve on the appliance 

discharges periodically, this may be due to thermal expansion in a closed water 
supply system. Contact the water supplier or local plumbing inspector on how to 
correct this situation. Do not plug the combination temperature and pressure relief 
valve outlet. 

 

9.  A combination sacrificial anode rod/hot water outlet nipple has been installed to 

extend tank life. The anode rod should be inspected periodically (every 2 years) 
and replaced when necessary to prolong tank life. Water conditions in your area 
will influence the time interval for inspection and replacement of the anode rod. 
Contact the plumbing professional who installed the water heater, or the 
manufacturer listed on the rating plate for anode replacement information. The use 
of a water softener may increase the speed of anode consumption. More frequent 
inspection of the anode is needed when using softened (or phosphate treated) 
water. 

 

 

Contact your supplier or plumbing professional for replacement parts or contact the 
company at the address given on the rating plate of the water heater. 
Provide the part name, model and serial numbers of the water heater when ordering 
parts. 

 

READ THE WARRANTY FOR A FULL EXPLANATION OF THE LENGTH 
OF TIME THAT PARTS AND THE WATER HEATER ARE WARRANTED. 

 

WARNING 

When lifting lever of the combination temperature and pressure relief 
valve, hot water will be released under pressure. Be careful that any 
released water does not result in bodily injury or property damage.

 

 

WARNING 

Do not run out of propane gas. Damage to the water heater may occur. 

 

WARNING 

THIS WATER MAY BE HOT.

 

 

CAUTION 

FOR YOUR SAFETY, 

DO NOT 

ATTEMPT REPAIR OF COMBINATION GAS 

CONTROL, BURNERS OR GAS PIPING. REFER REPAIRS TO A QUALIFIED 
SERVICE TECHNICIAN. 

Summary of Contents for RG275H10N

































Reviews: