Bradford White 45085E Installation & Operating Manual Download Page 31

 

31

Maintenance continued-

 

 

To inspect or replace an anode: 

The anodes on this water heater are easily accessible from the top of 
the heater making replacement simple and quick. 

a.

 

Turn the water heater electricity off for the zone containing 
the indirect-fired water heater. Flow water until the 
discharge is cool or allow enough time for the potable water 
to cool naturally. Connect a hose to the drain valve. Locate 
the hose’s discharge in an area where any remaining hot 
water will not cause any damage or injury. 

b.

 

Open the drain valve to flush any sediment out of the 
bottom to the heater. 

c.

 

Shut off the cold water supply. Make sure all hot water 
fixtures and circulating pumps are turned off. 

d.

 

Wait for water flow from the hose to stop. Remove the 
anode using a socket of the appropriate size. Do not use an 
impact wrench. 

e.

 

Inspect and replace the anode as required. Use pipe tape or 
sealant when reinstalling the anode. 

f.

 

Close the drain valve. Open a hot water fixture to allow air 
to escape. Open the cold water supply to the heater and 
allow the tank to fill.  

g.

 

Check your anode and drain valve for leaks. 

h.

 

Turn the water heater electricity on for the zone containing 
the indirect-fired water heater.  

4.

 

Sediment (Annual, but harsh water quality may dictate more 
frequent service)- 

Depending on water conditions, a varying 

amount of sediment may collect in the tank. Levels requiring 
service are indicated by a small temperature difference in the 
supply and return lines (See also “Scale” below). Repeated 
flushing usually clears such material. As a preventive measure, 
water should be drawn from the tank at the drain valve until it 
runs clear.

 

5.

 

Scale (Annual)- 

Hard water may cause scale to build-up on the 

outside of the heat exchanger coil. A water softener will prevent 
this problem (See also “Sediment” above). Symptoms would be 
reduced recovery capacity or reduced temperature differential 
between boiler supply and return lines. Repeated flushing should 
resolve the problem.

 

Summary of Contents for 45085E





































Reviews: