back side
| 09
| 13
| 11
| 15
| 10
| 14
| 12
| 16
Charging time
Charging time
Bluetooth Range
Play time
Mic Sensitivity
1.5 hrs (from 0-100)
2.5 hrs (from 0-100)
10m
2 hrs
WARNING–When using this product, basic
precautions should always be followed, including
the following:
Fully read the instructions before using the
product.
The unit will only achieve full performance after
2 or 3 completed charge and discharge cycles.
Do not overcharge your case. The unit may
become hot under excessive use. Remove your
case once it is fully charged. Never charge your
case for more than 7 hours at a time.
To reduce the risk of injury, close supervision is
required when the product is used near children.
Do not expose the device to moisture.
Do not use the device in excess of its output
rating. Overload outputs above the rating may
result in a risk of fire or injury.
Do not use the device if damaged or modified.
Damaged or modified batteries may exhibit
Changes or modifications not expressly
approved by the party responsible for compliance
could void the user’s authority to operate the
equipment.
This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment generates
uses and can radiate radio frequency energy
and, if not installed and used in accordance with
the instructions, may cause harmful interference
to radio communications. However, there is
no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning
the equipment off and on, the user is encouraged
to try to correct the interference by one or more of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment
and receiver.
Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV
technician for help.
This device complies with part 15 of the FCC
rules. Operation is subject to the following two
conditions (1) this device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation.
unpredictable behaviour resulting in fire,
explosion or risk of injury.
Do not disassemble the device. Take the device
to a qualified technician if service or repair is
required. Incorrect reassembly may result in a
risk of fire or injury.
Do not expose the device to fire or excessive
temperatures. Exposure to fire or temperatures
above 212ºF/100°C may cause explosion.
Have servicing performed by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the product
is maintained.
Mobile devices cannot connect with the earbuds if
the earbuds are not in pairing mode.
If the earbuds are unable to connect to a mobile
device via Bluetooth for 5+ minutes, the earbuds
will power off automatically.
Earbud Tech Specifications
Power Case Tech Specifications
Items
Items
Specifications
Specifications
Start-up failure
No sound when
paired
No indication
during charging
Shut down
automatically
Noise during
calls
Low volume
Signal
interrupted
low battery
wrong pairing
Earbuds aren’t
securely inserted
low battery
mobile device is
too far away
earbuds are
turned down low
environment
disturbance,
distance to far
from mobile
device
charge earbuds
and power case
re-pairing
check earbuds,
and try again
charge earbuds
and power case
bring mobile
device closer
adjust earbuds to
comfort & sound
bring the mobile
device closer to
the earbuds
Troubleshooting
Safety Precautions
FCC Statement
Issue
Reason
Solution
1.
2.
3.
4.
5.
6.
7.
8.
•
•
-
-
-
-
•
9.
10.
11.
12.
MADE IN CHINA
-42+3db
Power ON: Long press the multifunction
button for about 3 seconds, the indicator
lights will flash blue/red & a warning tone
will sound.
Long press the multi-functional button for
5 seconds, the indicator lights will flash red
and blue. Connect through Bluetooth, search
“Braavos” & click connecting, It will pair
automatically.
Single Earbud Usage:
2. Power ON/OFF
3. Once the earbud is successfully connected
with your device, you can listen to audio.
Power OFF: Long press the multifunction
button for about 5 seconds, the red LED
will light once, then Off, and a warning tone
will sound.
4. Answer/End calls: Press the multi-button
once to answer an incoming call, and again
to end.
5. Reject a call: Press and hold the
multifunction button to reject an incoming call.
6. Redial: Double press the multifunction
button to redial the last number you dialed.
7. Music: short press the button to pause the
music or play the music.
1. Pairing for the first time
Now turn on your mobile devices blueooth. If
done successfully only one “Braavos” pairing
name will appear.
