Boyertown Furnace Solaia SL375 Installation And Operator'S Manual Download Page 2

 

Be Aware of Hazard Definitions 

Denotes presence of a hazard which, if ignored, will result in severe personal injury, 
death or property damage 

Danger 

 

Denotes presence of a hazard which, if ignored could result in severe personal injury, 
death or substantial property damage. 

Warning

 

Denotes the presence of a hazard, which if ignored, could result in minor personal 
injury or property damage 

Caution 

 

Intended to bring attention to information, but not related to personal injury or property 
damage. 

Notice 

Warning

 

 

               This equipment must be installed, adjusted, serviced and started only by a qualified service 
agency – an individual or agency, licensed and experienced with all codes and ordinances, and who 
is responsible for the installation and adjustment of the equipment.  The installation must comply 
with all local codes and ordinances and with the latest revision of the National Fire Protection 
Standard for Oil Burning Equipment, NFPA 31. 

Danger 

 

Read all instructions before proceeding.  Follow all instructions completely.  Failure to follow these 
instructions could result in equipment malfunction causing severe personal injury, death or 
substantial property damage. 

 

Do not alter this boiler in any way.  The manufacturer will not be liable for any damage resulting 
from changes made in the field to the boiler or its components or from improper installation.  
Failure to comply could result in severe personal injury, death, or substantial property damage. 

 

Your oil fired boiler is designed to burn No. 1 and No. 2 heating oil only.  Never use gasoline or a 
mixture of gasoline and oil. 

 

Do not store gasoline or other flammable vapors and liquids in the vicinity of this or any other 
appliance. 

 

The area around the boiler should be kept free and clear of combustible materials. 

 

Never burn garbage or refuse in your boiler. 

 

Never try to ignite oil by tossing burning papers or other material into your boiler. 

 

Do not attempt to start the burner when excess oil has accumulated or the boiler is full of vapors. 

 

D

  

 

o not operate boiler if the heat exchanger is damaged. 

Do not jumper, attempt to bypass or override any of the safety limit controls. 

 

Do not use this boiler if any part has been under water.  Immediately call a qualified service 
technician to inspect the boiler and replace any part of the boiler, control system or burner that has 
been under water. 

 

All installations must conform to the requirements of the authority having jurisdiction. Such 
applicable requirements take precedence over the general instructions of this manual. 

 

Where required by the authority having jurisdiction, the installation must conform to the American 
Society of Mechanical Engineers Safety Code for Controls and Safety Devices for Automatically 
Fired Boilers, ANSI/ASME CSD-1. 

 

 

 

                   Concealed  Damage-  If  you  discover  damage  to  the  burner,  boiler  or  controls  during 
unpacking, notify the carrier at once and file the appropriate claim. When calling or writing about 
the boiler please have the following information available:  the boiler model number and serial 
number which is located on the upper left front of the unit.  Record the model and serial number for 
future reference in the space provided in this manual. 

NOTICE 

Summary of Contents for Solaia SL375

































Reviews: