background image

Dear customer,

Welcome to B&W.

This product has been designed and manufactured to the highest quality standards. However, if something 
does go wrong with this product, B&W Loudspeakers and its national distributors warrant free of charge 
labour (exclusion may apply) and replacement parts in any country served by an official B&W distributor.

Limited Warranty

This limited warranty is valid for a period of five years from the date of purchase or two years for electronics 
including amplified loudspeakers.

Terms and Conditions

The warranty is limited to the repair of the equipment. Neither transportation, nor any other costs,       

        nor any risk for removal, transportation and installation of products is covered by this warranty.

This warranty is only valid for the original owner. It is not transferable.

This warranty will not be applicable in cases other than defects in materials and/or workmanship at    

        the time of purchase and will not be applicable:

 

a)  for damages caused by incorrect installation, connection or packing,

 

b)  for  damages  caused  by  any  use  other  than  correct  use  described  in  the  user  manual,                  

             negligence, modifications, or use of parts that are not made or authorised by B&W,

 

c)  for damages caused by faulty or unsuitable ancillary equipment,

 

d)  for damages caused by accidents, lightning, water, fire heat, war, public disturbances or any                       

             other cause beyond the reasonable control of B&W and its appointed distributors,

 

e)  for products whose serial number has been altered, deleted, removed or made illegible,

 

f)  if repairs or modifications have been executed by an unauthorised person.

This guarantee complements any national/regional law obligations of dealers or national distributors  

        and does not affect your statutory rights as a customer.

How to claim repairs under warranty

Should service be required, please follow the following procedure:

If the equipment is being used in the country of purchase, you should contact the B&W authorised    

 

dealer from whom the equipment was purchased.

If the equipment is being used outside the country of purchase, you should contact B&W national    

 

distributor in the country of residence who will advise where the equipment can be serviced. You can  

 

call B&W in the UK or visit our web site to get the contact details of your local distributor.

To validate your warranty, you will need to produce the warranty form, completed and stamped by your dealer on 
the date of purchase. Alternatively, you will need the original sales invoice or other proof of ownership and date of 
purchase.

Warranty

2

Summary of Contents for CT XO
































Reviews: