Boss Snowrator MAG Owner'S Manual Download Page 4

Page: 4 / 16

causes distractions; otherwise, injury or property
damage may occur.

•

Do not operate the attachment near bystanders.

Safety and Instructional Decals

Safety decals and instructions are easily visible to the operator and are located near any area
of potential danger. Replace any decal that is damaged or missing.

decal139-8895

139-8895

Warning—read the

Operator’s Manual

Thrown object
hazard—keep bystanders
away.

Cutting/dismemberment
hazard of foot,
auger—stay away from
moving parts.

Warning—remove the key
from the ignition before
servicing the machine.

decal139-8896

139-8896

Cutting/dismemberment hazard of foot, auger—keep
bystanders away.

decal144-1299

144-1299

Cutting/dismemberment
hazard of hand; impeller

Do not place your hand in
the chute.

decalmsc27245

MSC27245

Warning—stay away from moving parts; keep all guards
and shields in place

Summary of Contents for Snowrator MAG

















Search results

Summary of Contents for Snowrator MAG

Reviews:

Related manuals for Snowrator MAG

Brands by name

Popular brands

Boss Snowrator MAG, Owner'S Manual

Search results

Summary of Contents for Snowrator MAG

Reviews:

Related manuals for Snowrator MAG

Brands by name

Popular brands