background image

- 2 -

Important

Read and understand all instructions before you use your product. If you do not follow 

the instructions in this manual, we are not responsible for any resulting personal injury or 

damage to property. This will also void the warranty.

Important Safety Precautions

•  Be sure to observe the following guidelines:

 - Do not increase speaker volume so high that you cannot hear what is around you.
 - Use caution or temporarily discontinue use in potentially hazardous situations.

•  Do not make any adjustment on the product when driving or in other situations where 

distractions can be hazardous. Responsible and safe driving is your primary responsibility when 

operating a vehicle.

•  Start volume at a low setting then gradually increase the volume until you can hear it 

comfortably, without sound distortion or ear discomfort.

•  In the event of smoke, strange noise or odor emitted from the product or any other abnormal 

operational signs appearing on the product, disconnect the product from the power supply. 

Discontinue use and contact your dealer or our technical support. Using the product in this 

condition may result in permanent damage to the product.

•  Servicing must only be carried out by a technician. Contact our technical support for any service 

questions.

Installation Precautions

•  WARNING: Always consult a professional installer.

•  Installation must be performed by a professional. Contact our technical support for any 

installation questions.

•  Before installation, disconnect the negative terminal of the vehicle battery to prevent damage to 

the product, fire, and/or possible injury.

•  Use only installation parts provided with the product. Using other mounting methods may void 

the warranty.

•  Observe the safety and operating instructions of the devices which are connected to the product. 

•  Important! 

Replace the faulty fuse with the same type and rating. Using a different type or 

rating of use may result in damage to the product or vehicle, or cause a fire.

• 

Do not use any aggressive cleaning agents. Clean the product with a dry, fiber-free cloth.

•  This product is water resistant against splashing water. Do not submerge the product in water 

under any circumstances.

Environmental Care

Do not throw away the product with normal household waste at the end of its life. Follow your local 

laws if/when disposing of electronic products. By doing this, you help preserve the environment.

Summary of Contents for MC425BA













Reviews: