FX Parameter
4
PITCH SHIFTER (FxPS: )
Parameter
Explanation
Voice
1-VOICE
One-voice pitch-shifted sound output in monaural .
2-MONO
Two-voice pitch-shifted sound (PS1, PS2) output in monaural .
2-STEREO
Two-voice pitch-shifted sound (PS1, PS2) output through left and
right channels .
Mode1
Mode2 *1
FAST,
MEDIUM,
SLOW
The response is slower in the order of FAST, MEDIUM and SLOW, but
the modulation is lessened in the same order .
MONO
MONO is used for inputting single notes .
* You may be unable to produce the intended effect when playing
chords (two or more notes played simultaneously) .
Pitch1
Pitch2 *1
Adjusts the amount of pitch shift (the amount of interval) in semitone steps .
Fine1
Fine2 *1
Make fine adjustments to the interval . The amount of the change in the Fine 100 is
equivalent to that of the Pitch 1 .
P. Delay1
P. Delay2 *1
Adjusts the time from when the direct sound is heard until the pitch shifted sounds
are heard . Normally you can leave this set at 0 ms .
* When set to BPM, the value of each parameter will be set according to the value
of the “MASTER BPM” specified for each patch . This makes it easier to achieve
effect sound settings that match the tempo of the song .
* If, due to the tempo, the time is longer than the range of allowable settings, it is
then synchronized to a period either 1/2 or 1/4 of that time .
F. Back1
Adjusts the feedback amount of the pitch shift sound .
E. Level1
E. Level2 *1
Adjusts the volume of the pitch shifter .
D. Level
Adjusts the volume of the direct sound .
*1: Setting not available when Voice is set to 1-VOICE .
HARMONIST (FxHrm: )
Parameter
Explanation
Voice
1-VOICE
One-voice pitch-shifted sound output in monaural .
2-MONO
Two-voice pitch-shifted sound (PS1, PS2) output in monaural .
2-STEREO
Two-voice pitch-shifted sound (PS1, PS2) output through left and
right channels .
Harm1
harm2 *1
Determines the pitch of the sound added to the input sound, when you are making
a harmony .
It allows you to set it by up to 2 octaves higher or lower than the input sound .
P. Delay1
P. Delay2 *1
Adjusts the time from when the direct sound is heard until the pitch shifted sounds
are heard . Normally you can leave this set at 0 ms .
* When set to BPM, the value of each parameter will be set according to the value
of the “MASTER BPM” specified for each patch . This makes it easier to achieve
effect sound settings that match the tempo of the song .
* If, due to the tempo, the time is longer than the range of allowable settings, it is
then synchronized to a period either 1/2 or 1/4 of that time .
F. Back1
Adjusts the feedback amount of the pitch shift sound .
E. Level1
E. Level2 *1
Adjusts the volume of the pitch shifter .
MastrKey
The key setting corresponds to the key of the song (#, b) as follows .
Major
Major
Minor
Minor
D. Level
Adjusts the volume of the direct sound .
*1: Setting not available when Voice is set to 1-VOICE .
PEDAL BEND (FxP. Bnd: )
Parameter
Explanation
Pitch
Sets the pitch at the point where the EXP Pedal is all the way down .
Position
Adjusts the pedal position for pedal bend .
This parameter is used after it’s been assigned to an EXP Pedal or similar controller .
E. Level
Adjusts the volume of the pitch bend sound .
D. Level
Adjusts the volume of the direct sound .
PHASER (FxPhasr: )
Parameter
Explanation
Type
4STAGE
A four-phase effect . A light phaser effect is obtained .
8STAGE
An eight-phase effect . It is a popular phaser effect .
12STAGE
A twelve-phase effect . A deep phase effect is obtained .
BiPHASE
The phaser with two phase shift circuits connected in series .
Rate
Sets the rate of the phaser effect .
* When set to BPM, the value of each parameter will be set according to the value
of the “MASTER BPM” specified for each patch . This makes it easier to achieve
effect sound settings that match the tempo of the song .
* If, due to the tempo, the time is longer than the range of allowable settings, it is
then synchronized to a period either 1/2 or 1/4 of that time .
Depth
Determines the depth of the phaser effect .
Manual
Adjusts the center frequency of the phaser effect .
Reso
Determines the amount of resonance (feedback) . Increasing the value will
emphasize the effect, creating a more unusual sound .
Step Rate
Sets the cycle of the step function that changes the rate and depth . When it is set
to a higher value, the change will be finer . Set this to “Off” when not using the Step
function .
* When set to BPM, the value of each parameter will be set according to the value
of the “MASTER BPM” specified for each patch . This makes it easier to achieve
effect sound settings that match the tempo of the song .
* If, due to the tempo, the time is longer than the range of allowable settings, it is
then synchronized to a period either 1/2 or 1/4 of that time .
E. Level
Adjusts the volume of the phaser .
D. Level
Adjusts the volume of the direct sound .
FLANGER (FxFlngr: )
Parameter
Explanation
Rate
Sets the rate of the flanging effect .
* When set to BPM, the value of each parameter will be set according to the value
of the “MASTER BPM” specified for each patch . This makes it easier to achieve
effect sound settings that match the tempo of the song .
* If, due to the tempo, the time is longer than the range of allowable settings, it is
then synchronized to a period either 1/2 or 1/4 of that time .
Depth
Determines the depth of the flanging effect .
Manual
Adjusts the center frequency at which to apply the effect .
Reso
Determines the amount of resonance (feedback) . Increasing the value will
emphasize the effect, creating a more unusual sound .
Separatn
Adjusts the diffusion . The diffusion increases as the value increases .
Low Cut
Sets the frequency at which the low cut filter begins to take effect . When “Flat” is
selected, the low cut filter will have no effect .
E. Level
Adjusts the volume of the flanger .
D. Level
Adjusts the volume of the direct sound .
TREMOLO (FxTrml: )
Parameter
Explanation
Wave Shape
Adjusts changes in volume level . A higher value will steepen wave’s shape .
Rate
Adjusts the frequency (speed) of the change .
* When set to BPM, the value of each parameter will be set according to the value
of the “MASTER BPM” specified for each patch . This makes it easier to achieve
effect sound settings that match the tempo of the song .
* If, due to the tempo, the time is longer than the range of allowable settings, it is
then synchronized to a period either 1/2 or 1/4 of that time .
Depth
Adjusts the depth of the effect .
E. Level
Adjusts the volume .
PAN (FxPan: )
Parameter
Explanation
Type
AUTO
Varies the volume level on the left and right according to the settings
for Wave Shape, Rate, and Depth .
MANUAL
Output uses the volume balance set with Manual Position .
Wave Shape
*1
Adjusts changes in volume level .
A higher value will steepen wave’s shape .
Rate *1
Adjusts the frequency (speed) of the change .
* When set to BPM, the value of each parameter will be set according to the value
of the “MASTER BPM” specified for each patch . This makes it easier to achieve
effect sound settings that match the tempo of the song .
* If, due to the tempo, the time is longer than the range of allowable settings, it is
then synchronized to a period either 1/2 or 1/4 of that time .
Depth
Adjusts the depth of the effect .
M. Position *2
Adjusts the volume balance between the left and right channels .
E. Level
Adjusts the volume .
*1: Setting available when Type is set to AUTO .
*2: Setting available when Type is set to MANUAL .
