background image

Troubleshooting

Problem

Possible Cause

Corrective Action

1. The controller is not plugged into the

wire harness.

1. Plug in the controller.

2. The electrical system is damaged.

2. Contact your authorized BOSS dealer.

The controller has no power.

3. A fuse is blown.

3. Replace the fuse.

1. The spreader and vehicle wire

harnesses are not connected.

1. Connect the wire harnesses.

The spreader motor does not work.

2. The controller is not plugged into the

wire harness.

2. Plug in the controller.

Material is spreading too fast.

1. The feed gate is open too much.

1. Move the feed gate lever to the

appropriate setting.

1. The spinner disk is stuck.

1. Refer to the Freeing a Clog section.

2. The spinner shaft is bent.

2. Inspect the spinner shaft and replace

it if damaged.

2 LED’s on the controller are flashing.

3. The spinner disk is contacting the

material deflector.

3. Clean off the material deflector.

1. There is a short between the controller

and the spreader.

1. Check the wire harness between the

spreader and controller. Repair or
replace it if damaged.

3 LED’s on the controller are flashing.

2. The spinner motor has an internal

short.

2. Replace the spinner motor.

1. The spreader is not connected to the

controller.

1. Connect the spreader to the controller.

2. The connection between the spreader

and controller connectors is bad.

2. Clean the connectors.

4 LED’s on the controller are flashing.

3. The spreader or controller are

connected to the wrong wire harness
connectors.

3. Ensure that the spreader and controller

are connected to the correct wire
harness connectors.

5 LED’s on the controller are flashing.

1. The battery voltage is low.

1. Increase the engine rpm and turn the

controller off then on again. If the
problem persists, turn off the vehicle
pump, lights, vibrator, and spreader,
increase the engine rpm, and let the
machine run for several minutes.
Check the voltage until your volt meter
reads 12 V, then turn the controller off
then on again.

6 LED’s on the controller are flashing.

1. The voltage regulator is bad.

1. Replace the voltage regulator.

7 LED’s on the controller are flashing.

1. The controller is overheating.

1. Turn the controller off until it cools

down.

12

 

 

Summary of Contents for SNR24030













Reviews: