Boss Snowplow MSC14175 Owner'S Manual Download Page 2

This product complies with all relevant European
directives; for details, please see the separate product
specific Declaration of Conformity (DOC) sheet.

BOSS Products limited consumer warranty and BOSS
Products commercial warranty policies are located at

www.bossplow.com

.

Patents

www.ttcopats.com

.

Introduction

Note:

This plow attaches to the Groundsmaster 7200

or 7210 with the Polar Trac kit or the Groundsmaster
360 with the Quick-Attach System.

The straight-blade plow is intended to be used on a
Toro ride-on, multi-purpose machine. The blade is
designed to hydraulically change its angle as needed
for snow removal. Using this product for purposes
other than its intended use could prove dangerous to
you and bystanders.

Read this information carefully to learn how to operate
and maintain your product properly and to avoid
injury and product damage. You are responsible for
operating the product properly and safely.

Visit

www.bossplow.com

for product safety and

operation training materials, accessory information,
help finding a dealer, or to register your product.

Whenever you need service, genuine BOSS parts, or
additional information, contact an Authorized BOSS
Dealer or BOSS Technical Service (1-800-286-4155)
and have the model and serial numbers of your
product ready.

Figure 1

identifies the location of the

model and serial numbers on the product. Write the
numbers in the space provided.

g324605

Figure 1

1.

Model and serial number location

Date
Purchased

Model No.

Serial No.

Blade Crate
Serial No.

This manual identifies potential hazards and has
safety messages identified by the safety-alert symbol
(

Figure 2

), which signals a hazard that may cause

serious injury or death if you do not follow the
recommended precautions.

g000502

Figure 2

Safety-alert symbol

This manual uses 2 words to highlight information.

Important

calls attention to special mechanical

information and

Note

emphasizes general information

worthy of special attention.

© 2020—BOSS Products
P.O. Box 787
Iron Mountain, MI 49801

2

Contact us at www.bossplow.com.

Printed in the USA

All Rights Reserved

 

Summary of Contents for MSC14175













Reviews: