background image

(BRIDGED SWITCH : MASTER POSITION)

(BRIDGED SWITCH : SLAVE POSITION)

To Inputs of 

Satellite Amplifier

From Outputs of 
Head Unit

SPEAKER IMPEDANCE

4 - 8 OHMS!

Electrical Wiring

Mounting the Amplifier

Fuses

     

                                                 

When making electrical connections to the amplifier, please observe the following:

All BOSS series power amplifiers are equipped with easy top access screw 
terminals. These terminals are n

in order to ensure excellent

electrical contact and to resist corrosion.

ickel-plated 

    Use at least 8 gauge or heavier wire for power and ground connections.
    Wire the amplifier directly to the car battery. Make sure there is circuit protection 
    (such as a fuse) on the positive power lead, within 18 inches of the battery.
    For the ground connection, use the shortest possible wire to a good chassis 
    ground point.
    Wire the Remote connection to the remote turn-on lead of your equalizer or head
    unit. In some cases this may be the power antenna lead of the head unit.

 

Fuses protect both the amplifier and the electrical system of your vehicle from 
faulty conditions. If you must replace the fuse in your Riot amplifier, use a fuse 
of exactly the same type and rating. A different type or rating may result in damage 
or cause a fire.

Mark the location for the mounting screw holes by positioning the amplifier where 
you wish to install it and use a scribe (or one of the mounting screws) inserted in 
each mounting hole to mark the mounting surface. If the mounting surface is carpeted, 
measure the hole centers and mark with a felt tip pen.

Drill pilot holes in the mounting surface for the mounting screws and insert the mounting
screws into these holes. Tighten them securely.

Note: Before beginning your installation, be sure to take note of any wires, lines or 
other devices in your vehicle which may be located behind any mounting surface.

Your BOSS digital amplifier is equipped with a dashboard mount remote subwoofer 
level control. Run the supplied dashboard remote control from the front panel of 
your amplifier. By turning the level knob clockwise, you will increase the output 
of low frequencies.

Remote Subwoofer Level Control

Bridging Two Amplifiers

GT1500D and GT2500D

Summary of Contents for GT1500D








Reviews: