Bose RoomMatch Utility RMU105 Installation And Safety Manuallines Download Page 12

Installation and Safety Guidelines 

English  15

pro.Bose.com

 Installation

Recommended Signal Processing

Digital signal processing (DSP) equipment is required for infrasonic protection and amplifier power limiting functions.  This processing is 

available in optional products from Bose such as the PowerMatch

®

 amplifiers and/or ControlSpace

®

 DSP hardware.

The following table lists the recommended infrasonic bandpass protection and amplifier limiter settings for each RoomMatch

®

 Utility 

loudspeaker when used without optional subwoofers:

Bandpass

Limiter

High Pass

Low Pass

V Peak

V RMS

Speaker

Type

Freq.

Type

Freq.

Threshold

Attack

Release

Threshold

Attack

Release

RMU208

BW24

70

BW24

20000

98.0

1.5

100.00

49.0

1000.00

2000.00

RMU206

BW24

80

BW24

20000

89.0

1.5

100.00

44.5

1000.00

2000.00

RMU108

BW24

80

BW24

20000

80.0

1.5

100.00

40.0

1000.00

2000.00

RMU105

BW24

90

BW24

20000

56.5

1.5

100.00

28.0

1000.00

2000.00

Technical Specifications

RMU208

RMU206

RMU108

RMU105

System Performance

Frequency Response (±3 dB)

(1)

80 – 16 kHz

90 – 16 kHz

90 – 16 kHz

100 – 16 kHz

Frequency Range (–10 dB)

70 – 16 kHz

80 – 16 kHz

80 – 16 kHz

90 – 16 kHz

Coverage Pattern, Horizontal

90° (rotatable)

120° (rotatable)

90° (rotatable)

100° (rotatable)

Coverage Pattern, Vertical

60° (rotatable)

60° (rotatable)

60° (rotatable)

100° (rotatable)

Long-Term Power Handling, Bose

(2)

300 W

250 W

200 W

100 W

Long-Term Power Handling, AES

(3)

400 W

300 W

250 W

150 W

Calculated Maximum SPL@1 m, peak

(4)

128 dB

123 dB

123 dB

118 dB

Transducers

Low Frequency

2 x Bose 8-inch woofer

2 x Bose 6.5-inch woofer

1 x Bose 8-inch woofer

1 x Bose 5.25-inch woofer

High Frequency

1 x Bose EMB2 compression driver

Nominal Impedance

8 ohms  (70V / 100V optional)

Physical

Dimensions (H x W x D), inches

9.3" x 27.0" x 10.5"

7.0" x 19.0" x 9.0"

9.3" x 18.5" x 10.5"

6.0" x 12.0" x 7.5"

Dimensions (H x W x D), mm

236 x 686 x 267 mm

178 x 483 x 229 mm

236 x 470 x 267 mm

152 x 305 x 191 mm

Net Weight

37 lb (16.8 kg)

25 lb (11.3 kg)

21 lb (9.5 kg)

12 lb (5.4 kg)

Net Weight with U-Bracket

43 lb (19.5 kg)

30 lb (13.6 kg)

26 lb (11.8 kg)

15 lb (6.8 kg)

Finish Color

black or white

Environmental Rating

Indoor

Notes:

1.  Frequency response and range measured on-axis, in an anechoic environment.
2.  Long-Term Power Handling, Bose Extended-Lifecycle Test.
3.  Long-Term Power handling, AES Transducer Test.
4.  Maximum SPL calculated from acoustic half-space sensitivity and AES power handling specifications, exclusive of power compression.

Summary of Contents for RoomMatch Utility RMU105















Reviews: