background image

English 

 21

Installation Guide 

 PowerShare PS604D/PS404D

pro.Bose.com

Technical Information

Technical Specifications

PS604D

Power Rating

Amplifier Power

4 × 150 W (THD+N < 0.04% 1 kHz, 4–8 Ω, 70/100 V)

Maximum Power per Channel

600 W @ 4–8 Ω, 70/100 V

Gain (Low-Z mode)

32.0 dB

Gain (70 V mode)

35.0 dB

Gain (100 V mode)

38.0 dB

Audio Performance

Frequency Response

4–8 Ω: 20 Hz to 20 kHz (± 0.5 dB @ 1 W);  70/100 V: Same as 4–8 Ω with 50 Hz high-pass filter

Channel Separation (Crosstalk)

> 85 dB @ 1 kHz, > 65 dB @ 20 kHz

Signal to Noise Ratio

100 dB (at rated power, A-weighted)

Audio Inputs

Analog

Dante

®

Input Channels

4 balanced

4 digital

Connectors

12-pin Euroblock

RJ-45 (primary)

Input Impedance

20 kΩ

Maximum Input Level

20 dBu (at 12 dBu sensitivity setting)

Sensitivity

4 / 12 dBu (low/high sensitivity)

Audio Outputs

Analog

Dante

Outputs

4

4 digital

Connectors

8-pin inverted Euroblock

RJ-45 (secondary)

Integrated DSP

A/D and D/A Converters

24-bit / 48 kHz

Processing Functions

Matrix mixer, loudspeaker EQ, real-time 9-band PEQ, V

Pk

/V

RMS

 limiters, delay, band pass, mute/

output polarity inversion

Audio Latency

< 1 ms (Analog input to analog loudspeaker output)

Indicators and Controls

Power LED

Solid green: Power is on. Blinking green: Unit is in standby mode. Solid amber: Thermal fault.  
Solid red: Supply fault.

Input Signal LED

Green: Signal present. Amber: Input is near clipping. Red: Input is clipping.  
Solid red: Indicates a fault.

Output Limit LED

Amber: Amplifier limiting an output. Blinking red: Amplifier muted. Solid red: Indicates a fault.

Controls, Front Panel

Power On/Off

Controls, Rear Panel

Output attenuators

Electrical

Mains Voltage

100 VAC to 240 VAC (±10%, 50/60 Hz)

AC Power Consumption

120 VAC: 14 W (Standby), 700 W (Max)

230 VAC: 14 W (Standby), 700 W (Max)

Mains Connector

Standard IEC (C14)

Maximum Inrush Current

14.14 A (230 VAC / 50 Hz), 8.04 A (120 VAC / 60 Hz)

Protections

High temperature, output short, extra high frequency (EHF), excessively low or high AC line voltage

Physical

Dimensions (H × W × D)

44 mm × 483 mm × 414 mm (1.7 in × 19.0 in × 16.3 in)

Shipping Weight

7.8 kg (17.2 lbs)

Net Weight

6.4 kg (14.1 lbs)

Cooling System

Microprocessor controlled, variable speed fans, left to right air flow

General

Inputs (Control)

Mute input control

Summary of Contents for PowerShare PS404D

























Reviews: