Bose Panaray LT MB24 III Reference Manual Download Page 27

Page: 27 / 40

Service Information

This section contains information on servicing Panaray

LT cabinets.

• Ordering information for replacement parts

• Painting information

• Replacement instructions for transducers or diaphragms

• Drawings of each cabinet type

Note:

Service should only be performed by a qualified audio professional.

Panaray

Replacement Parts

To order replacement parts, call the Bose

Customer Service center nearest you. Request parts by the part number in the

left hand column above

Replacement part

Product

Part number

3202-III Grille (includes screws)

3202

-III

276843

4402-III Grille (includes screws)

4402

-III

276844

9402-III Grille (includes screws)

9402

™

-III

276845

9702-III Grille (includes screws)

9702

-III

276846

Replacement Screws for grille

All

276847

Replacement Logo

All

276848

Input panel w/crossover board 3202

3202-III

276851

Input panel w/crossover board 4402

4402-III

276852

Input panel w/crossover board 9402

9402-III

276853

Input panel w/crossover board 9702

9702-III

276854

Compression driver

All

276860

Diaphragm for compression driver

All

276861

Compression driver plate w/screws

All

276849

V2 assembly with drivers

All

276850

Grille w/screws, tape, logo, tape, fastener and
spring

MB24-III

278244

Screws for grille

MB24-III

276847

Logo with tape, fastener and spring

MB24-III

276848

Input panel w/molex connector

MB24-III

278245

Woofer

MB24-III

278248

Summary of Contents for Panaray LT MB24 III









































Search results

Summary of Contents for Panaray LT MB24 III

Reviews:

Bose Panaray LT MB24 III, Reference Manual, Page: 27 / 40

Search results

Summary of Contents for Panaray LT MB24 III

Reviews: