background image

7

Setting Up

Front left and right cube speaker arrays

The front left and right cube speaker arrays create a sound image wider than the screen that 
seems natural to viewers sitting anywhere in the room. You can place the cube speaker arrays 
near a TV screen with no picture interference. Place the front cube speaker arrays on either 
side of your TV, at least 6 feet (2m), or as much as 15 feet (5m) apart (see Figure 2). 

Rear cube speaker arrays

The rear, or surround cube speaker arrays add discrete sounds and special effects that 
expand the visual image, bringing the viewer into the center of the action. The rear cube 
speaker arrays may carry dialogue as well. 

• Position the left and right rear cube speaker arrays to allow the sound to reach the viewer 

from both sides, rather than from directly behind (see Figure 2).

• Place the rear cube speaker arrays at ear height (when seated) or higher, if possible.

• Rotate the top and bottom sections of the rear cube speaker arrays to direct the sound to 

the front and back of the listener.

• If you have a center rear cube speaker array (Acoustimass 16 system or upgraded Acousti-

mass 15 Series II system), place it so that it is centered between the rear left and right cube 
speaker arrays (see Figure 2).

Powered Acoustimass

®

 module

Bose

®

 Acoustimass speaker technology takes advantage of the fact that the source of pure 

bass sound is difficult to locate, so you can hide the powered Acoustimass module conve-
niently out of sight. Place the module at the same end of the room as the television monitor. 

• You may hide the module behind furniture, but do not block the opening. Be sure there is at 

least 2 inches (5 cm) between any surface and the front opening or the grille on the bottom. 

• If the opening faces the wall it increases the bass; if it faces away it decreases the bass. 

CAUTION:

To prevent interference, keep the module at least 2 feet (.6m) from your TV set.

Figure 4

Powered Acoustimass 
module placement

Note:

Placing the module horizontally, or on 

its side, may reduce ventilation, inhibiting its 
ability to play at full output for extended 
periods of time.

AM264924_00 _V.pdf • August 13, 2002

Summary of Contents for Acoustimass 15 Series II

























Reviews: