19.
Stay alert.
Watch what you are doing. Use common sense. Do not operate a power tool when you are
tired.
20.
Check for damaged parts
. Before using a tool, check that there are no damaged parts, if a part is
slightly damaged carefully determine if it will operate properly and perform its intended function other
wise replace. Check for alignment of moving parts binding of moving parts, breakage of parts, free
running of moving parts, proper mounting and any other conditions that may affect the operation of the
tool. A guard or other parts that are damaged should be properly repaired or replaced by an authorised
service centre, unless otherwise indicated in this instruction manual. Defective switches must be replaced
by authorised service facility. Do not use the tool if the switch does not turn the tool on and off correctly.
21.
Warning
. The use of any accessory or attachment, other than those recommended in this instruction
manual, may present a risk of personal injury.
22.
Have your tool repaired by a qualified person
. This electric tool is in accordance with the relevant
safety requirements. Repairs should only be carried out by qualified persons using original spare parts;
otherwise this may result in considerable danger to the user.
23.
Do not let a tool run unattended
. Always wait until your power tool has come to a complete stop
before leaving it. Then turn off at mains and remove the plug from the power outlet.
WARNING
The use of an accessory or attachment, other than those recommended in this instruction manual may present a risk
of personal injury
The tool must be used only for its prescribed purpose any use other than those mentioned in this manual will be
considered a case of misuse. The user and not the manufacture shall be liable for any damage or injury resulting
from such cases of misuse.
ADDITION SAFETY RULES FOR ANGLE GRINDER
•
Fully unwind cable drum extensions to avoid potential overheating.
•
When an extension cable is required, you must ensure that it has the right ampere rating for your
Power tool and is in safe electrical condition.
•
Ensure your mains supply voltage is the same as your tool rating plate voltage.
•
Always switch off before you put the angle grinder down.
•
Keep the area free of tripping hazards.
•
Do not let anyone under the age of 18 years operate this tool.
•
Rags, cloths, cord, string and the like should never be left around the work area.
•
If you are interrupted when operating the tool, complete the process and switch off before looking up.
•
Periodically check that all the nuts, bolts and other fixings are properly tightened.
•
Abrasive wheels shall be stored and handled with care in accordance with manufactures instructions.
•
Do not store materials or equipment above a machine in such a way that they could fall into it.
•
Do not use discs having a maximum permissible speed below the tool rated marked RPM.
•
Inspect the grinding wheel before use, do not use chipped, cracked or otherwise defective products. Check the
disc before mounting it into the angle grinder. Check by striking it with a wooden handle whilst balancing the
disc on your finger. Listen to the sound it makes if it rings it is ok if it sounds dull it may be cracked and needs
to be replaced.
•
Ensure that mounted wheels and points are fitted in accordance with the manufacturers instructions.
•
When the disc is installed, run it for at least a minute to ensure that it does not have a fault. It is
always advisable to stay out of the line of the disc when testing or in general use.
•
Do not use a disc marked with a lower RPM than that of the no load speed shown on the rating plate.
•
Use discs only of the prescribed diameter.
•
Never try to operate the angle grinder without the guard in place .
•
Do not use separate reducing bushings or adaptors to adapt large hole abrasive wheels.
•
For tools intended to be fitted with threaded hole wheel, ensure that the thread in the wheel is long enough to
accept the spindle length.
•
Do not use cutting off wheel for side grinding.
•
Ensure that sparks resulting from use do not create a hazard e.g. do not hit persons or ignite flammable
substances.
•
Ensure that ventilation openings are kept clear when working in dusty conditions. If it should become
necessary to clear dust, first disconnect the tool from the mains supply (use non metallic objects) and avoid
damaging internal parts.
•
If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly
qualified person in order to avoid hazard
.
Page 4
