background image

INSTALLATION

6 720 807 912 (2015/10)

8

▶ Push the air inlet inner section through the side panel opening into the 

air box until it meets the stops [4] on the clamp assembly

▶ Centralise the inner elbow pipe within the elbow.
▶ Fit the elbow onto the flue cowl.
▶ Tighten the clamp [1] onto the flue elbow.

Fig. 14

[1]

Clamp, flue elbow

[2]

Air inlet inner section

[3]

Air inlet outer section

[4]

Clamp stops

[5]

Clamp bracket

▶ Drill through the air inlet outer section [3], with the 3.3mm drill bit, 

into the inner section [2] and secure the two sections with the self 
tapping screw.

Fig. 15

▶ Drill through the clamp tab [6] on the mounting bracket, with the 

3.3mm drill bit, into the air inlet outer section and secure with a self-
tapping screw.

Fig. 16 Tab detail

4.5

ALL FLUE OPTIONS, FINAL ASSEMBLY

▶ Lightly grease the flue pipe seal with the solvent free grease supplied.
▶ Remove the screw from the clamp bracket [1] and open the clamp.
▶ Insert the terminal [3] fully into the 80mmØ flue pipe.
▶ Pass the flue pipe [2] through the clamp bracket [1] and push into the 

flue cowl or elbow.

Fig. 17 Final assembly

[1]

Clamp bracket

[2]

Flue pipe

[3]

Terminal

▶ Drill two holes into the terminal [3] through the tabs [5], with the 

3.3mm drill bit, one either side, and secure the terminal [3] to the 
tabs [5] using the two self tapping screws.

▶ Fit the air box cover [4] over the lip on the top of the air box and 

secure the bottom two screws removed earlier.

Fig. 18

[4]

Air box cover

[5]

Tab

6720807912-14.1Wo

1

2&3

4

5

6720807912

-15.1W

o

3.3mmØ

6720807912

-16.1W

o

3.3mmØ

6

6720807912-17.1Wo

3

1

2

6720807912

-18.1W

o

4

1

5

3

Summary of Contents for Worcester Greenstar Oilfit External













Reviews: