background image

33

Glossary

6 720 801 019 (2012/05)

Room thermostat / programmer

A room thermostat / programmer must be fitted to control the 
central heating. This controls the times and temperatures of the 
central heating, preventing the boiler from firing unnecessarily. 
Refer to the instructions supplied with the thermostat and 
programmer for further information.

Thermostatic radiator valves

Thermostatic radiator valves must be fitted in sleeping 
accommodation. It is recommended that this type of valve is fitted 
to all but one of the radiators. The remaining radiator, where the 
room thermostat is located, must be uncontrolled and left open.

Pump over run function

After the boiler has finished a demand for central heating or hot 
water, the pump may continue to run for a short while to dissipate 
the heat from within the boiler.

Pump anti-seizure

If there has been no heating demand for 24 hours the boiler will 
run the system pump for a few seconds to reduce the possibility 
of pump seizure during long periods of inactivity.

SEDBUK

Seasonal Efficiency of Domestic Boilers in the UK.

Summary of Contents for Worcester Greenstar 24





































Reviews: