Bosch WAW32698SN Instruction Manual And Installation Instructions Download

Page: 49 / 56

Positioning and connecting

Connection

■

Drainage into a washbasin

■

Drainage into a siphon

The connection point must be

secured using a hose clamp with a

diameter of 24 - 40 mm (available

from specialist dealers).

■

Drainage into a plastic pipe with

rubber bushing or into a drainage

pit

Levelling

Align the appliance using a spirit level.
Incorrect alignment may result in loud

noises, vibrations and machine

"movement".

Loosen the lock nuts using a WAF17

spanner, by turning it in a clockwise

direction.

Check the alignment of the washing

machine with a spirit level, and

adjust it if necessary. Change the

height by turning the appliance feet.

All four appliance feet must stand

firmly on the ground.

The lock nuts on all four appliance

feet must be screwed tightly against

the housing using a suitable WAF17

spanner. In doing so, hold the foot

tight and do not adjust its height.

Summary of Contents for WAW32698SN

























































Search results

Summary of Contents for WAW32698SN

Reviews:

Related manuals for WAW32698SN

Brands by name

Popular brands

Bosch WAW32698SN, Instruction Manual And Installation Instructions

Search results

Summary of Contents for WAW32698SN

Reviews:

Related manuals for WAW32698SN

Brands by name

Popular brands