ʑ
8"48
8"48
8"48
ʑ
ć
Â
10
Care
Machine housing, control panel
Wipe with a soft, damp cloth.
Do not use abrasive detergents.
Immediately remove laundry and cleaning agent residues.
Do not clean the appliance with a water jet.
Clean the detergent drawer ...
... if it contains detergent or fabric softener residue.
1.
Pull out the drawer up to the stop position, press down the latch on the
insert and remove the drawer completely .
2.
Remove insert: pull insert upwards with finger.
3.
Clean the detergent dispenser and the insert with water and a brush.
4.
Refit the insert and secure in place (the cylinder should fit over the guide
pin).
5.
Insert the detergent drawer.
Leave detergent drawer open so that residual water can evaporate.
Drum
Leave washing machine door open after washing so that the drum can dry out.
Rust stains use chlorinefree cleaning agent, not steel wool.
Descaling
No laundry in the machine!
This should not be necessary if the detergent is dispensed correctly. However, follow the
instructions of the descaler manufacturer.
Information on the display
Please close the door immediately because of rising water level; in pause status,
and
are displayed alternately.
Door is locked due to safety reasons (water level and/or temperature are too high); in
pause status,
and
are displayed alternately. If you need to open the door,
wait for the temperature to drop or drain the water (e.g. select
Spin
programme).
Door cannot be locked/unlocked due to high temperature of the door lock. Wait a moment
and try again.
+
Tap turned ?
Inlet filter blocked ? Clean filter
a
page 11
.
Supply hose kinked or blocked ?
The symbol
flashes, indicating the laundry inside are unbalanced. The washing
machines unbalanced load detection system can not adjust the imbalance.To protect the
mechanical systems, the machine will not achieve the highest spin speed, and the laundry
can not be spinned completely. Please wash small and large items of laundry together.
Clean detergent solution pump
a
page 11
;
outlet pipe/drainage hose blocked.
other displays
Switch off the appliance, wait 5 seconds and switch it back on.
If the display appears again, call the customer services.
a
page 13 or the Warranty Card
Risk of electric shock!
Pull out the mains plug!
Risk of explosion! No solvents!
11
Risk of scalding!
Allow detergent solution to cool down!
Turn off the tap!
Maintenance
Drain pump blocked
Set programme selector to
Â
Off
, pull out the mains plug.
1.
Open service flap.
2.
Take the drainage hose out of the holder.
3.
Remove sealing cap, allow detergent solution to flow out. Have a suitable
container ready.
Push up the closing cap and place the drain hose back in its holder.
4.
Carefully unscrew the pump cover (Caution! residual water).
Clean the interior, pump cover thread and pump housing (fan impeller
in the detergent-solution pump must rotate).
5.
Reinsert and screw on pump cover. Handle should be vertical.
6.
Close the service flap.
To prevent unused detergent from flowing into the outlet during the next
wash: Pour 1 litre of water into dispenser
II
and start the
Spin
programme.
Filter blocked in water inlet hose
Release water pressure in the supply hose:
1.
Turn off the tap!
2.
Select any programme (except
Spin
).
3.
Press
Start
/Reload button. Leave programme for approx. 40 seconds.
4.
Set programme selector to
Â
Off
. Pull out the mains plug.
Clean the filter:
5.
Disconnect the hose from the water tap.
Clean filter with small brush.
or
remove hose from the rear of the appliance.
Take out filter with pliers and clean.
6.
Connect the hose and check for leaks.
ʑ
ʑ
a
ʑ
a
a
a
ʑ
ʑ
a
ʑ
a
ʑ
ʑ
a
ʑ
ʑ
~
a
ʑ
ʑ
ʑ
a
a
ʑ
ʑ
ʑ
ʑ
Â
Â
a
ʑ
a
ʑ
ʑ